background image

The Status Light (cont’d)

REmOTE START DiAGnOSTiCS

  The remote start system can also indicate which zone caused the last remote start 

cycle to end� To see this indicator, place the system into alarm valet mode� Immedi-

ately after the chirp, the status light will flash to indicate which zone violation occured.

1 FLASh:

 Run time expired�

2 FLAShES:

 Brake pedal was pressed or the hood was opened�

3 FLAShES:

 Engine stalled or a bad tach signal�

4 FLAShES:

 Received transmitter command to stop�

5 FLAShES:

 The neutral safety circuit was triggered�

6 FLAShES: 

The alarm was triggered or low battery voltage�

Anti-Carjacking Protection

  The system is equipped with two separate Anti-Carjacking protection features 

(ignition, open door, or both) that are selectable via user feature #12�  Once activated, 

the user has 60 seconds to cancel the Anti-Carjacking protection process (described 

below)�  If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren 

will begin to chirp for 7 seconds to alert the user that the system is about to enter into 

an alarm condition�  The Valet Switch may still be pressed once during this period to 

cancel the Anti-Carjacking process�

  If the Anti-Carjacking process is not cancelled before the 60 second countdown 

expires, the system will enter an alarm condition, sounding the siren and flashing the 

parking lights�   30 seconds after this occurs, or should the ignition be turned off in the 

meantime, the stater interrupt will engage� Once the system enters the alarm condi-

tion, it will not respond to the transmitter, nor will the system reset automatically after 

60 seconds, and it can only be disengaged by:

Step 1

  Turning the vehicle’s ignition off�

Step 2

  Turning the ignition back on�

Step 3 

 Within 5 seconds, perform an Emergency Override using the Valet Switch�  

NOTE: SecureCode (see user feature #13) is required if it has been customized.

TyPES OF AnTi-CARJACKinG PROTECTiOn

ignition Activated Anti-Carjacking 

activates every time the vehicle’s ignition is 

turned on�  The Valet Switch must be pressed within 60 seconds of activating to 

cancel Anti-Carjacking�

Door Anti-Carjacking 

activates when a door is opened after the vehicle is started 

and the engine is running�  The Valet Switch must be pressed within 60 seconds after 

activation to cancel Anti-Carjacking�

10

Summary of Contents for AL-1660-EDPB





















Reviews: