OS3030
Alarm signals
12
Low-pressure signal 1
Í ·
¹ ² ¿ ´
î ö
Ô ± © ó
° ® » - - ò
ï
ê ð -
The "low-pressure" input has been activated.
The system cuts out and is then switched back
on again after the time shown in the bottom
right. The number of switch-on attempts is
shown in the top right.
The LCD and LED displays are cancelled once
the "low-pressure" signal is cleared when the
system is re-started.
The system can be switched on before the
delay elapses by pressing "ON".
Warning! The buzzer and alarm relay, if one
has been programmed, are not activated yet.
Possible cause: The system settings have
been changed.
Low-pressure signal 2
Í ·
¹ ² ¿ ´
Ô ± © ó
° ® » - - « ® »
î
The "low-pressure" input has been activated.
The system cuts out.
The display is cancelled and the system
switched back on once the "low-pressure"
signal is cleared.
If the alarm relay or the horn has been acti-
vated, the alarm relay and the horn must be
cancelled manually.
This is only displayed if 0 has been entered in
step 5.6 of the basic programming procedure.
The system can be switched on manually by
pressing "ON".
Possible causes: No pressure in the untreated
water, the pre-filter is blocked.
Low-pressure signal 3
Í ×
¹ ² ¿ ´
Ô ± © ó
° ® » - - « ® »
í
The "low-pressure" input has been activated.
The system cuts out.
The system must be switched back on manu-
ally. The LCD cannot be cancelled before then.
This signal is only displayed if the system has
unsuccessfully tried to come back on auto-
matically, despite the lack of water, or if 1 has
been entered in step 5.6 of the basic pro-
gramming procedure.
The system can be switched on straight away
by pressing "ON".
Possible causes: No pressure in the untreated
water, the pre-filter is blocked.
Concentrate signal 1
Í ×
¹ ² ¿ ´
î ö
Ý ± ² ½ » ² ¬
® ò
ï
ë ð -
The "concentrate" input has been activated.
The system cuts out and is then switched back
on again after the time shown in the bottom
right. The number of switch-on attempts is
shown in the top right.
The LCD and LED displays are cancelled once
the "concentrate" signal is cleared when the
system is re-started.
The system can be switched on before the
delay elapses by pressing "ON".
Warning! The buzzer and alarm relay, if one
has been programmed, are not activated yet.
Possible cause: The system settings have
been changed.
Concentrate signal 2
Í ×
¹ ² ¿ ´
Ý ± ² ½ » ² ¬
® ¿ ¬
»
î
The "concentrate" input has been activated.
The system cuts out.
The display is cancelled and the system
switched back on once the "concentrate" signal
is cleared.
If the alarm relay or the horn has been acti-
vated, the alarm relay and the horn must be
cancelled manually.
This is only displayed if 0 has been entered in
step 5.3 of the basic programming procedure.
The system can be switched on manually by
pressing "ON".
Possible causes: The system settings have
been changed.
Concentrate signal 3
Í ×
¹ ² ¿ ´
Ý ± ² ½ » ² ¬
® ¿ ¬
»
í
The "concentrate" input has been activated.
The system cuts out.
The system must be switched back on manu-
ally. The LCD cannot be cancelled before then.
This signal is only displayed if the system has
unsuccessfully tried to come back on auto-
matically, despite the lack of water, or if 1 has
been entered in step 5.3 of the basic pro-
gramming procedure.
The system can be switched on straight away
by pressing "ON".
Possible causes: The system settings have
been changed.
