EWM Tetrix XQ 350 AC/DC puls Operating Instructions Manual Download | Manualshive

Page: 42 / 63

background image

Maintenance, care and disposal

Maintenance schedule

42

099-005674-EW501

28.06.2022

6.3.3 Heat exchanger (torch cooling)

WARNING

Risk of injury due to insufficient training!

Appropriate training is required for the following maintenance steps to prevent injuries.

• Only authorised service personnel may carry out this maintenance step.

• Note the warnings and maintenance instructions at the beginning of this chapter!

Figure 6-6

• Switch off the machine and disconnect the mains plug. Remove the screws of the side panel. Remove

the side panel from the system (lift up and sidewards).

• Use only compressed air free of water and oil. Do not blow on electronic components directly. The ma-

chine fans may over-rev due to the compressed air and thus become damaged. Therefore, use a

screwdriver to block the machine fan mechanically. Please note: The strips of the heat exchanger be-

hind the machine fans must not be damaged by the screwdriver.

Figure 6-7

• Blow out the heat exchanger using the fans.
• The dirt escapes through the openings in the side panel.

Follow official regulations on disposal!

• After cleaning, remove any mechanical blockages from the fans, close the machine in reverse order

and check according to applicable regulations.

«
...
40
41
42
43
44
...
»

Summary of Contents for Tetrix XQ 350 AC/DC puls
































































Reviews:

No comments

Related manuals for Tetrix XQ 350 AC/DC puls

Brand: Harbor Freight Tools Pages: 32

Brand: Generac Power Systems Pages: 2

Brand: All-Power Pages: 14

Brand: Altrad Pages: 56

Brand: Atlas Copco Pages: 68

Brand: Sylvania Pages: 24

Brand: Tektronix Pages: 12

Brand: Vitek Pages: 6

Brand: Power Tech Generators Pages: 24

Brand: Harbor Freight Tools Pages: 22

Brand: Sound Pro Pages: 8

Brand: Philips Pages: 1

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 14

Brand: Philips Pages: 14

COLOR TV 19 INCH PORTABLE 19PR15C

Brand: Philips Pages: 20

Brand: Curtis Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands