EWM SATURN MIG 200, Operating Manual

Page: 51 / 68

10 Maintenance and Care
10/1
These welding machines require very little maintenance. However, depending upon the amount of
dust occurring, the unit should be cleaned as described below and visually checked at least every 4
- 6 months.
In so doing, the unit must be reliably isolated from the mains power supply.
PULL OUT THE MAINS PLUG!
(Switching off or pulling out a fuse does not give adequate isolation protection)
- Remove both side walls.
- Tighten all screw and crimped connections and visually check the unit.
- Scorched areas should be checked and corrected by a specialist..
- Replace any faulty power leads.
Treat the individual components as follows:
Power Source
out with oil and water free compressed air depending upon the amount of dust present.
Electronics, Printed Circuit Boards
The electronic components may not be blow clean with compressed air but should be cleaned
off with a vacuum cleaner.
Torch with Hosepack
Protect thehosepack from hot components. Blow out or replace the wire guide spiral or the Teflon
liner. No great increase in the hole through the contact nozzle is permissible. Replace with new in
good time.
Drive Rollers
These rollers are subject to normal wear. If the counter-roller brings the correct pressure the
welding wire must be fed smoothly. If the counter-rollers and the drive rollers touch with wire in then
the drive rollers should be replaced (watch for possible undersized welding wire).
Coolant (KF 23E-10) and Check of the Cooling Unit
The coolant level in the UK 500 must be checked at regular intervals.
As soon as the fluid level falls by more than ¼ of the tank contents it must be topped up with more
coolant. Further, the coolant container should be regularly cleaned from dirt particles (by blowing
out or vacuuming) to ensure an optimum cooling of the welding torch.
Repairs
Repair and maintenance work may only be performed by qualified personnel. In all service matters,
always consult your dealer. Return deliveries of defective equipment subject to warranty may only
be made through your dealer.
When replacing parts, use only original spare parts.
When ordering spare parts, the machine type, serial number and item number of the machine, as
well as the type description and item number of the spare part must be quoted.
If repair or maintenance work is carried out on this machine by personnel who are not trained and
authorised to undertake such work, the right to claim under the warranty lapses.
Die im Kapitel
"Wa
rtung und
Pflege" aufgeführten H
inweis
e, Ric
htlinien und Normen w
urden
grundle
gend überarb
eitet und sind aus diesem G
rund nic
ht mehr gültig!
Die rele
vante
n Hinw
eise, R
ichtlinien und Normen fin
den Sie in den
beiliegenden
Ergänzungsb
lättern "A
llgemeine Hinweise
zu 3 J
ahre G
arantie
", Art.
Nr.: 09
9-000GAR-EWMxx.
Sollten die Dokumente nicht vorlie
gen, können diese über den autorisie
rten Fa
chhändler
angef
ordert we
rden!
Auße
rachtl
assung kann lebensg
efährlich sei
n!
The instructions, guidelines and standards given in
the "Maintenance and Care" chapter hav
e
been completely re
vised and are theref
ore no longer valid!
The releva
nt instru
ctions
, guidelines an
d standards can be f
ound in the enclosed supplements
"Gener
al notes on the 3 ye
ar war
ranty",
item no
.: 09
9-000GAR-EWMxx.
If these documents are missing, the
y can be reque
sted from you
r authorised sp
ecialist
dealer!
Not observing
these instruc
tions can be potentially fat
al!
Les consignes, dire
ctives
et norm
es indiquées au chapitre « Maintenance et entretien » ont été
mises à jour et ne sont donc plus v
alable
s !
Vous trouverez
les consignes
, directives e
t normes
applica
bles d
ans les additifs « Consignes
généra
les relatives
à la garantie
de 3 an
s », à l´article :
099-000GAR-EWMxx.
Si vou
s ne possédez pas les documents
, vous
pouv
ez vo
us les procurer auprès de vo
tre
revendeur autorisé
!
Le non-respect des consignes peut représenter un danger de
mort !
Le istruz
ioni, direttive
e norme
presenti nel capitolo „
Manut
enzion
e e cur
a” so
no state
completamente riviste
e per questo motivo
non sono più valide
!
Le istruz
ioni, direttive
e norme
rilev
anti le trova
te nell'aggiornam
ento qui allegato “Is
truzioni
genera
li sui 3 anni di
garan
zia”, Nr
. Art.:
099-000GAR-EWMxx.
Se i documenti non f
ossero disponibili, possono
essere richiest
i al rive
nditore autorizz
ato!
L'inosservan
za delle istruzioni può comportare
pericolo di vita!
D
F
GB
I