background image

34000 Autry Street, Livonia, MI 48150  |  800.968.5530  |  Fax 734.419.0209  |  www.hamiltonengineering.com  |  LIT91127US REV 5/2018

Page 67

SPECIAL INSTALLATION REQUIREMENTS

This  appliance  is  equipped  with  an  automatic  combustion  characteristic  adjustment  system,  provided  the                 

installed elevation above sea level is entered into the operating control (FMT 914) when the height is greater 

than 2,000 feet and less than or equal to 9,000 feet. To enter the operating elevation:

 

• 

Press the 

reset button

 continuously for 3 seconds, the appliance shows the adjusted altitude  

 

 

of the appliance (0 = sea level). Each time the 

service button

 is pressed, the value increases by 

 

 

100 feet (20 through 90 = 2,000 through 9,000 feet). After reaching the maximum value, the 

 

 

counter returns to the minimum value (example: when the value is 90 and the service button is 

 

 

pressed, the new value will be 20). When the right altitude has been set (example: 53 = 5,300 

 

 

feet of elevation above sea level), press the 

reset button 

for one second and the value will be 

 

 

programmed. The factory default is 20 (which equals 2,000 feet), and there is no need to adjust 

  below 

that. 

See Figure 8-3 on page 56 for the button locations.

 

 

• 

The adjusted altitude entered is internally converted to an offset on top of the maximum fan  

  speed.

 • 

By adjusting the combustion characteristics as described above, there is no de-rate

 

 

required at altitudes up to 9,000 feet. For elevations in excess of 9,000 feet or gas BTU 

 

 

content levels below 950 BTU/cubic foot, consult the factory at 734.419.0200 or 800.968.5530 

 

 

for adjustments and de-rating information.

B. INSTALLATION AT HIGH ALTITUDES

PART 10. WARRANTY INFORMATION

A. WARRANTY CONTACT INFORMATION

Hamilton Engineering, Inc. warrants each EVO™ Water Heater and Boiler to be free from defects in material 

and workmanship according to terms, conditions and time periods. 

Unless otherwise noted, these warranties 

commence on the date of installation.

 If required periodic maintenance is not performed, warranty coverage 

may be voided.

Warranty information specific to each model can be found on our website 

www.hamiltonengineering.com

,

requested via email at 

[email protected]

, or in our printed Product Catalogs.

If you have any questions or comments, please contact us at 800.968.5530. If you need emergency technical 

support after hours, we are available 24 hours a day, 7 days a week by calling this number.

Please keep the following information on hand when calling about warranty information:

Model: ___________________________ Serial #: _______________________________________________

Installer Name: ____________________ Phone #: ___________________ Install Date: _______________

Summary of Contents for HW 129




































































Reviews: