background image

4

evo HE H 

Installation & Servicing

GENERAL

Boiler Size

H12, H16, H19, H22

Gas supply type and connection

2H-G20-20 mbar Rc

1

/

2

  (

1

/

2

" BSP Female

)

Injector size

Stereomatic 5.6mm dia. (HE 12 5.8mm dia).

Flow connection

22mm copper

Return connection

22mm copper

Flue terminal diameter

mm (in.)

100 (4)

Maximum static water head

m (ft.)

30.5 (100)

Minimum static water head

 m (ft.)

0.45 (1.5)

Electrical supply

230 V ~ 50 Hz

Boiler power consumption

38W

Fuse  rating

External: 3A   Internal: T3.15A L250 V

Water content

litre (gal.)

1.7 (0.37)

Packaged weight

kg (lb.)

38 (84)

Maximum installation weight

kg (lb.)

31 (68)

Boiler size

Height  mm (in.)

582 (23)

Width  mm (in.)

390 (15)

Depth  mm (in.)

278 (11)

Boiler Size

H12  Max

H16  Max

H19 Max

H22 Max

H12 min

H16-22 Min

Boiler input 'Q' =

Nett CV

kW

12.2

16.4

19.5

22.6

9.8

9.1

Btu/h

41,600

56,000

66,500

77,100

33,400

31,000

Gross CV

kW

13.5

18.2

21.6

25.1

10.9

10.1

Btu/h

46,000

62,100

73,800

85,600

37,200

34,400

Gas consumption

 l/s (cu.ft/h) 0.35 (44.2) 0.47 (59.9) 0.56 (71.1) 0.65 (82.5) 0.28 (35.6)

0.26 (33.3)

Boiler output 'P' =

70 

o

C Mean water

       kW

12.0

16.1

19.0

22.0

9.3

8.8

temperature

Btu/h

40,900

55,000

65,000

75,000

31,800

30,000

40 

o

C Mean water

 kW

12.7

16.8

20.0

23.3

10.5

9.6

temperature

Btu/h

43,300

57,400

68,300

79,500

35,900

32,800

Seasonal efficiency (SEDBUK) *

Band A

[90.1]%

[90.4]%

[90.3]%

[90.2]%

NOx  classification

                    Class 5

*

The value is used in the UK Government's Standard Assessment Procedure (SAP) for energy rating of dwellings.
The test data from which it has been calculated have been certified by a notified body.

CAUTION.

To avoid the possibility of injury during the installation, servicing or cleaning

of this appliance, care should be taken when handling edges of sheet steel components.

Note.

Gas consumption is calculated using a calorific value of
38.7 MJ/m

3

 (1038 Btu/ft

3

) gross or 34.9 MJ/m

(935 Btu/ft

3

)

nett.  To obtain the gas consumption at a different calorific
value:-

a.

For l/s - divide the gross heat input (kW) by the gross
C.V. of the gas (MJ/m

3

)

b.

For ft

3

/h - divide the gross heat input (Btu/h) by the

gross C.V. of the gas (Btu/ft

3

)

Key to symbols

GB 

= United Kingdom

IE

 = Ireland

   

(Countries of destination)

PMS

= Maximum operating pressure of water

C

13 

C

33 

C

53

 

 = A room sealed appliance designed for connection via

ducts to a horizontal or vertical terminal which admits
fresh air to the burner and discharges the products of
combustion to the outside through orifices which, in this
case, are concentric. The fan is up stream of the
combustion chamber.

I

2H

=

An appliance designed for use on 2nd Family gas, Group
H only.

Table 2 - Performance Data

Table 1 - Boiler Data

203323-2.pmd

21/09/2007, 11:26

4

Summary of Contents for H12

























































Reviews: