Evikon T3511 Instruction Manual Download Page 3

Page: 3 / 26

IE-SNC-Tx5xx-03

General safety rules

The following summary is designed to prevent injury hazards or device damage. Operate the

instrument in accordance with this manual to prevent electric trauma.

Service should be performed by a qualified person only.

Precautions against injury or fire

Use a safety ac/dc adapter.

Use only an adapter with the power voltage recommended by its

manufacturer and which is approved by proper standards. Check that the adapter has undamaged
cables and cover.

Connect and disconnect correctly.

Do not connect and disconnect a LAN cable or lead-in cables if

the device is under electric voltage.

Do not use the instrument without the cover.

Do not use the instrument, if it does not work correctly.

If the instrument seems not to work

correctly, have it checked by a qualified service person.

Do not use the instrument in an explosive environment.

Summary of Contents for T3511



























Search results

Summary of Contents for T3511

Reviews:

Related manuals for T3511

Brands by name

Popular brands

Evikon T3511, Instruction Manual

Search results

Summary of Contents for T3511

Reviews:

Related manuals for T3511

Brands by name

Popular brands