evertz 7890IXG User Manual Download

Page: 65 / 70

7890IXG

Internet Exchange Gateway

Revision 2.3

Page - 57

CARD EDGE

7.1.

MODULE STATUS LEDS

Two large LEDs on the front of the main board indicate the general health of the module:

Local Fault:

This red led indicate poor module health or if a local input power fault exists( i.e.: a blown

fuse). The local fault indication an also be reported to the frame through the frame status jumper.

Module OK:

This green led indicates good module health. It will be on when the board is good.

7.2.

SERIAL PORT

This port j4 is used to communicate with the board. It allows the user to do initial set up of the card through
ribbon cable. To do initial set up through this port follow

set up

(procedure #3) in startup guide.

7.3.

USB PORT

This port is used for the same purpose as serial port.

Summary of Contents for 7890IXG







































































Search results

Summary of Contents for 7890IXG

Reviews:

Related manuals for 7890IXG

Brands by name

Popular brands

evertz 7890IXG, User Manual

Search results

Summary of Contents for 7890IXG

Reviews:

Related manuals for 7890IXG

Brands by name

Popular brands