evertz 7890IXG User Manual Download | Manualshive

Page: 11 / 70

background image

7890IXG

Internet Exchange Gateway

Revision 2.3

Page - 3

2.

GETTING STARTED

Figure

2-1 : 7890IXG Rear Panel

SFP Internet:

Ethernet port used for transferring and receiving data through unmanaged networks.
For example: the Internet.

LN/ACT SPD:

Ethernet Access 1 and 2 ports are used to interface the transport stream onto the
unmanaged network. For example these ports will interface with an encoder and/or
decoder for access to and from the internet.

ASI IN/OUT:

ASI input and output BNC.

USB:

This port allows the user to directly access the module serially by connecting directly
to a computer through USB cable. This USB port allows serial port access for initial
setup.

«
...
9
10
11
12
13
...
»

Summary of Contents for 7890IXG







































































Reviews:

No comments

Related manuals for 7890IXG

ASinterfoce AC1325

Brand: IFM Electronic Pages: 23

Brand: LOYTEC Pages: 150

Brand: SVS Pages: 4

GW1102-2DRS-485-TB-P

Brand: 3onedata Pages: 3

Brand: Pathport Pages: 3

Brand: Microhard Systems Pages: 186

Brand: Arris Pages: 2

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 134

Brand: SonicWALL Pages: 7

Brand: Mercury Pages: 5

Brand: Dr. Neuhaus Pages: 147

Brand: ViewSonic Pages: 39

Brand: VOPtel Pages: 38

Brand: Kaon Pages: 12

Brand: wowvision Pages: 145

Brand: 2Wire Pages: 131

Brand: Lauda Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands