evertz 7814UDX-4K Series User Manual Download | Manualshive

Page: 51 / 64

background image

7814UDX-4K Series

HD/3G/UHD Up/Down/Cross Converters

Revision 1.2

Page - 41

CC CDP Write Line:

The

CC CDP Write Line

parameter will set the closed captioning write line where the

VANC captions are inserted on the output video as per SMPTE 334M.

Loss of CC Timeout:

This parameter allows the user to set the amount of time (in Seconds) before the

Closed Captioning timeouts when the video is lost. To set the Loss of CC Timeout, drag the slider right to
decrease or left to increase the value. The value range is 1 to 600 seconds.

CEA 708 Service:

There are eight controls that will map closed caption and text channels into CEA708

caption services. For simplicity, only the selection control for the

CC1 to CEA708 Service

control will be

shown in the manual. This parameter will map CC1 into a CEA708 Caption Service. Currently, the
modules only support 16 services (1 to 16). When set to off, the CC1 is not mapped to any CEA708
Caption Service.

Off

CC1 will not be mapped to a CEA708 Service

1

CC1 will be mapped CEA708 Service 1

2

CC1 will be mapped CEA708 Service 2

3

CC1 will be mapped CEA708 Service 3

4

CC1 will be mapped CEA708 Service 4

5

CC1 will be mapped CEA708 Service 5

6

CC1 will be mapped CEA708 Service 6

7

CC1 will be mapped CEA708 Service 7

8

CC1 will be mapped CEA708 Service 8

9

CC1 will be mapped CEA708 Service 9

10

CC1 will be mapped CEA708 Service 10

11

CC1 will be mapped CEA708 Service 11

12

CC1 will be mapped CEA708 Service 12

13

CC1 will be mapped CEA708 Service 13

14

CC1 will be mapped CEA708 Service 14

15

CC1 will be mapped CEA708 Service 15

16

CC1 will be mapped CEA708 Service 16

5.11.2. Closed Captioning Status

The CDP monitor section enables the user to view CDP parameters that are monitored. This section is for
read-only purposes and the parameters herein can’t be modified.

CDP 708 Demux Status:

This parameter displays the status of 708 Closed Caption reading.

CDP Parser Status:

This parameter displays the status of Closed Caption reading.

5.12. ANC PASS THRU

The ANC Pass Thru feature allows the user to define specific rules for passing ANC data from input to
output. This allows ANC data that is normally not processed through the module to pass through without
getting striped on the output video signal.

There are two modes of operation for ANC Pass Thru,

Mapped ANC Pass Thru

and

Direct ANC Pass

Thru.

«
...
49
50
51
52
53
...
»

Summary of Contents for 7814UDX-4K Series

































































Reviews:

No comments

Related manuals for 7814UDX-4K Series

Brand: 3onedata Pages: 3

Brand: Icy Box Pages: 2

Brand: Hubner Pages: 28

Brand: Hewalex Pages: 2

DCS SCARLATTI DAC

Brand: Data Conversion Systems Pages: 26

Brand: B&B Electronics Pages: 2

Brand: Optical Systems Pages: 2

Brand: Baja Silueta Pages: 99

Brand: Delta Electronics Pages: 2

CONSONANCE REFERENCE DB1

Brand: Opera Pages: 3

INTERNATIONAL TRAVEL ADAPTER

Brand: Igo Pages: 1

Brand: Allied Telesis Pages: 52

Brand: Faulhaber Pages: 29

Brand: Balluff Pages: 2

Brand: Trycom Technology Pages: 20

Brand: Ferm Pages: 36

Brand: Prism Sound Pages: 63

PowerVerter Plus PV 1000FC

Brand: Tripp Lite Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands