evertz 570J2K-HW-X19 User Manual Download | Manualshive

Page: 34 / 60

background image

570J2K-HW-X19

Multi channel J2K Encoder-Decoder

Page - 24

Revision 1.0

Encoder Up Time:

This parameter displays the encoder up time, reflecting how long has the encoder

been running for.

5.7.

IP INPUT MONITOR

Figure

5-13 : WebEASY

®

- IP Input Monitor Tab

5.7.1. Input Stream

Stream Type:

This parameter displays the type of input stream which could be multicast or unicast.

Protocol Status:

This parameter reflects the input protocol. It will reflect unknown, UDP or RTP.

AES Encryption Detected:

This parameter displays if the stream has AES Encryption or not.

Received Ethernet Bandwidth:

This parameter displays the received Ethernet Bandwidth for each

input stream.

5.7.2. Input IP Packet Monitor

IP packet Drop Count:

This parameter displays the total count of sync loss.

IP Packet Bit Rate:

This parameter displays the IP Packet Bit rate.

«
...
32
33
34
35
36
...
»

Summary of Contents for 570J2K-HW-X19





























































Reviews:

No comments

Related manuals for 570J2K-HW-X19

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 9

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 3

Brand: 3onedata Pages: 7

Brand: Gama Sonic Pages: 4

Brand: Yamaha Pages: 31

Brand: Williams AV Pages: 2

Brand: Baja Silueta Pages: 99

Brand: Delta Electronics Pages: 2

CONSONANCE REFERENCE DB1

Brand: Opera Pages: 3

INTERNATIONAL TRAVEL ADAPTER

Brand: Igo Pages: 1

Brand: Premier Pages: 12

Brand: OTS Pages: 14

Pocket Inverter 100

Brand: XPower Pages: 38

Brand: Balluff Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands