background image

IMPORTANT SAFETY NOTICE 

 

PRECAUTIONS 

 

This exercise machine is built for optimum safety.  However, certain precautions apply 
whenever you operate a piece of exercise equipment.  Be sure to read the entire manual 
before you assemble or operate your machine.  In particular, note the following safety 
precautions: 
 
 

 1.  Keep children and pets away from the machine at all times.  DO NOT leave children 

unattended in the same room with the machine. 

 2.  Only one person at a time should use the machine. 
 3.  If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, 

STOP the workout at once.  CONSULT A PHYSICIAN IMMEDIATELY. 

 4.  Position the machine on a clear, leveled surface.  DO NOT use the machine near water or 

outdoors. 

 5.  Keep hands away from all moving parts. 
 6.  Always wear appropriate workout clothing when exercising.  DO NOT wear robes or other 

clothing that could become caught in the machine.  Running or aerobic shoes are also 
required when using the machine. 

 7.  Use the machine only for its intended use as described in this manual.  DO NOT use 

attachments not recommended by the manufacturer. 

 8.  Do not place any sharp object around the machine. 
 9.  Disabled person should not use the machine without a qualified person or physician in 

attendance. 

10. Before using the machine to exercise, always do stretching exercises to properly warm up. 
11. Never operate the machine if the machine is not functioning properly. 
12. A spotter is recommended during exercise. 

 

CARE AND MAINTENANCE 
 

1. Lubricate moving parts with WD-40 or light oil periodically. 
2. Inspect and tighten all parts before using the machine. 
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.  
     DO NOT use solvents. 
4. Maximum weight capacity 300 lbs. 

 

WARNING:  BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT 
YOUR PHYSICIAN.  THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS 
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH 
PROBLEMS.  READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS 
EQUIPMENT.  IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL 
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE 
OF THIS PRODUCT. 

 

SAVE THESE INSTRUCTIONS.

 

 
 

Summary of Contents for EVE-840

















Reviews: