menu SET CLOCK
Use this function to set current time and date. The control board is equipped with a lithium battery guaranteeing the time clock 3/5 year-long autonomy. Set the
current date by pressing OK and the respective arrows to increase or decrease the selected values.
menu CHRONO
Submenu – ENABLE CHRONO:
The menu shown on the "ENABLE CHRONO" display allows overall enabling and disabling of all the chronothermostat functions. To enable, press the P1
button. Press P3 button to confirm.
Submenu – DAILY CHRONO:
Once the "DAILY CHRONO" menu has been selected, the daily chrono is enabled using the P1 and P2 buttons. With the P4 button, the possible items can
be scrolled through, including: switch-on time, switch-off time, set stove heat output, room temperature. It is possible to set two operating ranges. The OFF
setting tells the clock to ignore the command. To change use the keys P1 and P2 while to confirm press P3.
Submenu – WEEKLY CHRONO:
The "WEEKLY CHRONO" menu allows enabling/disabling and setting of the weekly chronothermostat functions. The weekly programming function features
4 independent programmes. Moreover, if the time is set to OFF, the time clock ignores the corresponding control. To change use the keys P1 and P2 while to
confirm press P3.
In each program you will find: Switch-on time, Switch-off time, Set stove heat output, Room temperature, Days of the week for which the programme is to be
active. Monday is 1 and Sunday is 7.
Submenu – CHRONO WEEK-END
It is used to enable/disable and to set the chronothermostat functions on weekends (days 6 and 7, i.e. Saturday and Sunday). To enable, press the P1 and
P2 buttons. Setting the times
Start 1
and
Stop 1
sets the operating period for
Saturday
, while
Start 2
and
Stop 2
are used to set the stove operation for
Sunday.
In each program you will find: Switch-on time, Switch-off time, Set stove heat output, Room temperature.
menu SELECT LANGUAGE
Use this command to select one of the languages available. To move to the next language press P1 (increase) to go back, press P2 (decrease) and to confirm
press P4.
menu MODE BUZZER
It is used to enable or disable the buzzer board.
menu INITIAL LOAD
This function is only available when the stove is OFF and is used to load the auger when the stove is started for the first time when the pellet hopper is empty. After
selecting the menu, press P1. The exhaust blower switches on at the maximum speed and the auger tube (auger tube LED on) starts working. They will switch off
once the period of time indicated on the display has elapsed or after pressing the P3 button.
menu STOVE STATUS
Enter the STOVE STATUS menu, after pressing the P4 button, the display scrolls the status of a number of variables during operation of the stove at work.
menu TECHNICAL
This menu item is reserved for the stove installer.
menu STAND-BY
In this menu it is possible to activate or deactivate the automatic stand-by of the stove. When selected, if the conditions have all been met, the stove will enter
MODULAT – OK STDBY. This state lasts for 10 minutes. Once this time has elapsed, the stove will switch off and then switch on again when required.
USER FUNCTIONS
Standard functioning of a control board properly installed on an air stove is described below with reference to the functions available to users.
Stove ignition
Hold P3 button down for a few seconds to switch on the stove. Successful ignition is indicated on the display with the word "START". During this phase, the stove
goes into pre-heating status; both the glow plug (as indicated by the corresponding glow plug LED) and the exhaust blower switch on.
Any problem detected during the switching-on phase is indicated on the display and the stove goes into alarm status.
Loading with Pellets
After approximately 1 minute the pellet loading phase begins and the message "LOAD PELLETS" appears on the display. During the initial phase, the auger tube
loads the pellets into the fire pit for a fixed time. In the second phase the auger tube turns off, while the speed of the fumes and the glow plug remain in the previous
state. If ignition does not occur after this phase, the auger tube is switched on again and the glow plug remains on.
Fire present
Once fume temperature has reached and exceeded a pre-set threshold, the stove goes into the ignition mode and the message “FLAME LIGHT” appears on the
display. The speed of the fumes is fixed, the auger tube turns on for a fixed time and the glow plug is turned off. Any problem during this phase will cause the
control board to stop and the stove to go into error state.
Stove operational
After the temperature of the fumes has reached and exceeded a given value and has maintained it for at least a predetermined time, the stove goes into work
mode which is the normal working mode. The upper display shows the time and the room temperature and the lower one the set power and the power in which
the stove is found. The heat output can be set by pressing the P2 key and the room temperature can be set by pressing the P1 button. If the fume temperature
reaches a certain set threshold, the air exchanger fan turns on. After this phase, the stove cleans the fire pit. The word "CLEANING FIRE-POT" scrolls on the
display, the auger is on and the fume fan is on. Once the set period of time has elapsed, the stove goes back to the working mode.
14
