Eusso UGL2430-RTH User Manual Download

Page: 7 / 56

1.2 Package Contents

‧

One Wireless AP Router with 1 antennas

‧

One External Power Adapter

‧

One CD-ROM (user’s manual)

‧

One RJ-45 Ethernet Cable

1.3 System Requirements

‧

Computers with an installed Ethernet adapter.

‧

Valid Internet Access account and Ethernet based DSL or Cable
modem.

‧

10/100Base-T Ethernet cable with RJ-45 connector.

‧

TCP/IP protocol must be installed on all PCs.

‧

System with MS Internet Explorer ver. 5.0 or later, or Netscape
Navigator ver. 4.7 or later.

1.4 LEDs Indication & Connectors of Wireless Router

Front Panel LEDs Indication

LED Light

Status

Description

Wireless Router is powered on.

Power

Off

Wireless Router is powered off.

Slow Blinking

WLAN is successfully connected.

WLAN

Blinking

Data is being sent or received.

WAN port is successfully connected

WAN

Blinking

Data is being sent or received.

LAN port is successfully connected.

LAN

(1, 2, 3, 4)

Blinking

Data is being sent or received.

Summary of Contents for UGL2430-RTH
























































Search results

Summary of Contents for UGL2430-RTH

Reviews:

Related manuals for UGL2430-RTH

Brands by name

Popular brands

Eusso UGL2430-RTH, User Manual

Search results

Summary of Contents for UGL2430-RTH

Reviews:

Related manuals for UGL2430-RTH

Brands by name

Popular brands