manualshive.com logo in svg

Eurotech ZEUS, Technical Manual

Share
Download
Eurotech ZEUS Technical Manual Download Page 6

 

ZEUS Technical Manual 

Introduction 

© 2007 Eurotech Ltd    Issue D

 

6

 

Introduction 

The ZEUS is an ultra-low power, high performance, single board computer based on 

the PXA270 processor. The PXA270 is an implementation of the Intel XScale micro 

architecture, combined with a comprehensive set of integrated peripherals including: 

•

 

Flat panel graphics controller. 

•

 

Interrupt controller.  

•

 

Real time clock. 

•

 

Various serial interfaces.  

The ZEUS board is based on the EPIC form factor. Included as standard are: 

•

 

2 Ethernet ports. 

•

 

2 USB host ports.  

•

 

7 serial ports. 

The ZEUS includes a site for a variety of wireless modems and a GPS receiver, and is 

designed to create cost effective solutions in asset monitoring, asset tracking, mobile 

terminals and network communication controllers. The ZEUS also includes an onboard 

vehicle compatible DC/DC power supply to simplify system integration. 
The board is available in the standard variants specified in the following table: 

Variant Details 

ZEUS-M128-F32-001-R6 

 

Main features (all other features are included unless 

otherwise stated): 

•

 

Onboard DC/DC PSU. 

•

 

Dual Ethernet ports. 

•

 

LVDS transmitter. 

•

 

CAN bus controller. 

•

 

520MHz processor.  

This variant is included in the Development Kits. 

ZEUS-M128-F32-002-R6 
 

 

 

 

Main features (all other features are included unless 

otherwise stated): 

•

 

Dual Ethernet ports

. 

•

 

LVDS transmitter

. 

•

 

CAN bus controller

. 

•

 

5V only (No DC/

DC

 PSU). 

•

 

520MHz processor. 

continued…

Summary of Contents for ZEUS









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands