Eurotech ZEUS Technical Manual Download Page 16

Page: 16 / 136

ZEUS Technical Manual

Getting started

ZEUS Quickstart Manual

is provided with each Development Kit to enable you to set

up and start using the ZEUS board. Please read the relevant manual and follow the

steps explaining how to set up the board. Once you have completed this task, and your

ZEUS system is working, you can start adding further peripherals enabling

development to begin.

This section explains how to set up and use some of the features of the ZEUS. For

more detailed information on any aspect of the board see the section

Detailed

hardware description

page

Using the ZEUS

Using the CompactFlash socket

The ZEUS is fitted with a Type I/II CompactFlash socket mounted on the solder side of

the board. The socket is connected to Slot 0 of the PXA270 PC card interface. It

supports 3.3V Type I and II CompactFlash cards, for both memory and I/O. The ZEUS

supports hot swap changeover of the cards and notification of card insertion.

For more details see

Expansion interfaces

, page

5V CompactFlash cards are not supported.

Using the serial interfaces (RS232/422/485)

The four standard serial port interfaces on the ZEUS are fully 16550 compatible.

Connection to the serial ports is made via two DB9 connectors, a 20-way header and a

simple 5 way header. The pin assignment of the 20 way header has been arranged to

enable 9-way IDC D-Sub plugs to be connected directly to the cable. See the section

J19 – Serial ports – COM3/4

, page

, for pin assignments and connector details.

See the section

Serial COM ports

, page

, for further details.

Using the audio features

There are four audio interfaces supported on the ZEUS: amp out, line out, line in and

microphone. The line in, line out and amp interfaces support stereo signals and the

microphone provides a mono input. The amplified output is suitable for driving an 8

load with a maximum power output of 250mW per channel.

Connections are routed to J11. See the sections

, page

, page

, for further details.

Using the USB ports

The standard dual USB type ‘A’ connector is provided on the front panel. See the

sections

USB

, page

, and

J8 – USB connector

, page

, for further details.

Summary of Contents for ZEUS









































































































































Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands

Eurotech ZEUS, Technical Manual

Search results

Summary of Contents for ZEUS

Reviews:

Related manuals for ZEUS

Brands by name

Popular brands