Eurotech ZEUS Technical Manual Download Page 51

Page: 51 / 136

ZEUS Technical Manual

Detailed hardware description

USB

There are two USB host interfaces on the ZEUS. These comply with the Universal

Serial Bus Specification Rev. 1.1, supporting data transfer at full-speed (12Mbit/s) and

low-speed (1.5Mbit/s).

There are four signal lines associated with each USB channel: VBUS, DATA+, DATA-,

GND. The USB host ports are connected to a dual USB connector, type A (J8).

A USB power control switch controls the power and protects against short-circuit

conditions. If the USB voltage is short-circuited, or more than 500mA is drawn from

either supply, the switch turns the power supply off and automatically protects the

device and board. The VBUS power supply is derived from the ZEUS +5V supply. To

switch the VBUS1 and VBUS2 power on, use the PXA270 GPIO89 and GPIO22

respectively (set them to logic ‘1’).

USB port 2 can be configured as a client port internally within the PXA270 USB

controller, and is connected to 5-pin header J10.

For details of connector pinouts, see the sections

J8 – USB connector

, page

, and

J10 – USB client header

, page

More information about the USB bus and the availability of particular USB peripherals

can be found at

www.usb.org

Host port 2 on J8 and client port on J10 can only be used one at a time.

DO NOT connect both devices at the same time.

Summary of Contents for ZEUS









































































































































Search results

Summary of Contents for ZEUS

Reviews:

Brands by name

Popular brands

Eurotech ZEUS, Technical Manual

Search results

Summary of Contents for ZEUS

Reviews:

Brands by name

Popular brands