manualshive.com logo in svg

Eurotech ZEUS, Technical Manual

Share
Download
Eurotech ZEUS Technical Manual Download Page 36

 

ZEUS Technical Manual 

Detailed hardware description 

© 2007 Eurotech Ltd    Issue D

 

36

 

ZEUS Modem-1 supports the following modules: 

•

 

Sony Ericsson GR64, a quad-band (850/900/1800/1900) version of GR47/48. 

Functionally comparable to the Sony Ericsson GR47/GR48 devices, the GR64 

offers a broad range of voice and data features. The integrated TCP/IP stack 

enables effective use of GPRS. For further details see  

Sony Ericsson GR64

, 

page 

104

. 

•

 

Siemens MC35i/39i, a dual-band GSM/GPRS module (EGSM 900/1800MHz). For 

further details see 

Siemens MC35i/39i

, page 

106

. 

•

 

Fastrax iTrax03/8, a 12-channel GPS receiver. iTrax03/8 features low power 

consumption, small footprint, 8Mbit internal Flash and does not require battery 

backup. For further details see 

Fastrax iTrax03/8

, page 

108

. 

•

 

Motorola iO270, a wireless modem that provides packet data, circuit data and 

voice connectivity on the iDEN 800MHz network. The iO270 include a GPS 

receiver. For further details see 

Motorola iO270

, page 

110

. 

For further details about this modem see the section 

ZEUS Modem-1

, page 

118

. 

ZEUS Modem-2 supports the following wireless module with built-in GPS receiver:

 

•

 

Telit GE863-GPS module, which supports communication services in quad-band 

EGSM 850/900/1800/1900MHz networks. For further details see 

Telit GE863-GPS

, 

page 

112

. 

For further details about ZEUS Modem-2, see the section 

ZEUS Modem-2

, page 

118

. 

ZEUS Modem-3 supports the following wireless modules:

 

•

 

Sierra Wireless MC8775 PCI Express Mini Card embedded module, which offers 

connectivity to all three HSDPA/UMTS frequency bands (850, 1900, 2100 MHz) 

and all four EDGE/GPRS bands (850, 900, 1800 and 1900 MHz) used worldwide. 

For further details see 

Sierra Wireless MC8775

, page 

114

. 

•

 

Sierra Wireless MC5720 PCI Express Mini Card embedded module, which offers 

a complete wireless data solution over CDMA 1x EVDO networks with typical 

download data rates of 400-700 kbps. For further details see 

Sierra Wireless 

MC5720

, page 

116

. 

•

 

Fastrax iTrax03/16, a 12-channel GPS receiver. iTrax03/16 features low power 

consumption, small footprint, 16Mbit internal Flash and does not require battery 

backup. For further details see 

Fastrax iTrax03/8

, page 

108

. 

For further details about ZEUS Modem-3, see the section 

ZEUS Modem-3

, page 

119

. 

Summary of Contents for ZEUS









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands