Eurotech AIM104-COM8 Technical Manual Download Page 7 | Manualshive

Page: 7 / 25

background image

AIM104-COM8 Technical Manual

What items are provided?

© 2007 Eurotech Ltd Issue C

7

What items are provided?

The AIM104-COM8 is supplied with the following items:

•

The AIM104-COM8 board.

•

Mounting kit.

Getting started

Unpacking and connecting up

To begin using the AIM104-COM8 board, follow these steps:

1

Power down your computer.

2

Install the board in a spare PCI slot.

3

Power up your computer and install the appropriate driver available from our

website

www.eurotech-ltd.co.uk/en/downloads

«
...
5
6
7
8
9
...
»

Summary of Contents for AIM104-COM8


























Reviews:

No comments

Related manuals for AIM104-COM8

Brand: Gigabyte Pages: 104

Brand: Zetex Pages: 8

Brand: IEI Technology Pages: 131

Brand: Gigabyte Pages: 80

Brand: Advantech Pages: 82

DQ45CB - Desktop Board Executive Series Motherboard

Brand: Intel Pages: 96

Spacewalker AV40

Brand: Shuttle Pages: 81

Brand: MSI Pages: 6

Brand: ECS Pages: 43

Brand: SOYO Pages: 102

Brand: Analog Devices Pages: 4

Brand: Philips Pages: 22

TSB42AA9 (StorageLynx) EVM

Brand: Texas Instruments Pages: 32

Brand: Siemens Pages: 15

Brand: Siemens Pages: 26

Brand: Siemens Pages: 27

Brand: Siemens Pages: 39

Brand: MACCHIATObin Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands