manualshive.com logo in svg

European Home H Series, Installation & Operation Owner'S Manual, Page: 26 / 36

Share
Download
European Home H Series Installation & Operation Owner'S Manual Download Page 26

WARRANTY

26

H Series

 Vent Free Fireplace Rev #12042020                                                                                                                                European

Home

.com

European Home Warranty 

H Series Vent Free Gas Fireplace 

 
 

European Home warrants the H Series Vent Free Gas Fireplace burners against defects in materials and workmanship for a 
period of TWO (2) YEARS from the date of original retail purchase. We warrant the H Series Vent Free cabinet against defects 
in materials and workmanship for a period of FIVE (5) YEARS from the date of original retail purchase. If a defect exists, 
European Home will, at its option, either (1) provide needed components using new or refurbished replacement parts or (2) 
exchange the product with one which is new or which has been manufactured from new or serviceable used parts and is at 
least functionally equivalent to the original product. A replacement product/part assumes the remaining warranty of the 
original product or ninety (90) days from the date of replacement or repair, whichever provides longer coverage for you. 
When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes the 
property of European Home.  
 
Nothing in the above shall be deemed to imply that this warranty shall apply to work which has been abused or neglected 
or shows evidence of changes or modifications by others with or without permit, damages caused by the acts of God, 
building settlement or moving, fire or vandalism.  In addition, installation of this product that varies from the requirements 
stated in the instruction manual will void the warranty. 
 
 
 

European Home is a division of Europa Ja, Inc. 

 

 

Summary of Contents for H Series





































Reviews:

No comments