European Home H Series Installation & Operation Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 36

European Home H Series Installation & Operation Owner'S Manual Download Page 12

12

PRE-INSTALLATION PLANNING

H Series

Vent Free Fireplace Rev #12042020 European

Home

.com

Before you begin your installation you should have

the following tools and supplies:
•  Saw
•  Hammer
•  Pliers
•  Pipe wrench
•  Phillips and straight-blade screwdrivers
•  Plumb line and level
•  Tape measure and framing square
•  Electric drill and assortment of drill bits

•  Safety glasses and gloves
•  Framing material
•  Non-combustible finish material
•  Approved pipe joint sealant
•  Manometer
•  #6 or #8 self-tapping screws, 1/2” - 3/4” long
•  Leak detection fluid (non-corrosive) or electronic

gas detector

• Appropriate electrical supply wiring parts
• Appropriate gas supply line parts

BEFORE YOU BEGIN

Thank you for purchasing an

H Series

Vent Free Gas Fireplace. This fireplace has been designed to provide you

with safe, trouble-free operation.

Please read this manual thoroughly before beginning the installation of your fireplace. It has information which

is important for safe installation and operation.

Please inspect your shipment for completeness and any damage. Contact your retailer if any damage is found.

Do not install your fireplace with any damaged or substituted parts.

The installation of your new fireplace will follow the steps below and this manual is laid out accordingly.

•

Pre-Installation Planning

- Fireplace location, gas and electric supply runs and clearances

•

Rough Installation

- Build the rough frame and install the fireplace

•

Electric Installation

- By a qualified, licensed electrician

•

Gas Installation

- By a qualified, licensed gasfitter or plumber

•

Trim and Finish

- Finishing around the fireplace

•

Final Installation

- Wall, mantel and non-combustible facing

«
...
10
11
12
13
14
...
»

Summary of Contents for H Series





































Reviews:

No comments