manualshive.com logo in svg

European Home H Series, Installation & Operation Owner'S Manual, Page: 24 / 36

Share
Download
European Home H Series Installation & Operation Owner'S Manual Download Page 24

MAINTENANCE

24

H Series

 Vent Free Fireplace Rev #12042020                                                                                                                                European

Home

.com

A qualified service agency should conduct an annual inspection and maintenance of your 

H Series

 Vent Free Gas 

Fireplace to keep it running safely. The following procedures should be performed only by a qualified service 

person. The gas supply should be turned off whenever a maintenance procedure is performed. All parts of the 

fireplace that are removed for servicing must be replaced prior to operation.

Cleaning the Media and Burner

With all parts of the fireplace at room temperature, carefully remove and clean the fire media with a soft bristled 

brush. 

Lift off the hearth panel and clean the burner surface with a brush and clean the rest of the burner module, 

including the pilot burner, with a vacuum cleaner.  After lifting off the Hearth Panel, ensure that the Primary Air 

Openings (shown below, at the end of each Burner Inlet Tube) remains free of dust or debris.  These openings 

may cleaned with a vacuum cleaner or brush.

Primary Air Openings

Burner Inlet Tubes

Failure to keep the primary air opening of the burner clean may result in sooting 
and property damage.

W

ARNING

W

ARNING

Burner Close-up

Summary of Contents for H Series





































Reviews:

No comments