background image

Voyager 3000 User Guide

2-8

Table 2-1 SCSI ID switch settings for the second backplane in a VRA-3002 configuration.

DPS1 Sw1
(ID Bit0)

DPS1 Sw2
(ID Bit1)

DPS1 Sw3
(ID Bit2)

DPS1 Sw4
(ID Bit3)

Bay 0 Device SCSI ID

Off

Off

Off

Off

0

On

Off

Off

Off

1

Off

On

Off

Off

2

On

On

Off

Off

3

Off

Off

On

Off

4

On

Off

On

Off

5

Off

On

On

Off

6

On

On

On

Off

7

Off

Off

Off

On

8

On

Off

Off

On

9

Off

On

Off

On

10

On

On

Off

On

11

Off

Off

On

On

12

On

Off

On

On

13

Off

On

On

On

14

On

On

On

On

15

DPS1 Sw5
(ID Bit0)

DPS1 Sw6
(ID Bit1)

DPS1 Sw7
(ID Bit2)

DPS1 Sw8
(ID Bit3)

Bay 4 Device SCSI ID

Off

Off

Off

Off

0

On

Off

Off

Off

1

Off

On

Off

Off

2

On

On

Off

Off

3

Off

Off

On

Off

4

On

Off

On

Off

5

Off

On

On

Off

6

On

On

On

Off

7

Off

Off

Off

On

8

On

Off

Off

On

9

Off

On

Off

On

10

On

On

Off

On

11

Off

Off

On

On

12

On

Off

On

On

13

Off

On

On

On

14

On

On

On

On

15

Cabling and Termination Issues

SCSI requires that cable lengths be no greater than 6 metres at 5MHz clock rates and no
greater than 3 metres at 10MHz clock rates when used in SCSI -2 single ended mode.
Differential mode allows cable lengths of up to 25 metres. See the note below for Ultra SCSI.
This is summarised in Table 2-2.

Summary of Contents for Voyager 3000











































































Reviews: