These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by
any method, e.g. photocopy, microfi lming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. These ope-
rating instructions represent the technical status at the time of printing. Changes in technology
and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
SETTING THE TIME MANUALLY
If DCF reception is not possible, the watch can also be set manually.
However, the precondition is that the 12 o’clock positioning of the hands has been
performed correctly (see “Positioning the hands”) and no DCF signal has been
received.
-
Briefl y press the push-button (A).
-
The minutes are displayed in the display (C).
-
Now use push-button (A) to set the correct time.
Press briefl y: this will cause the position of the minutes hand to change gradu-
ally.
Press for longer: this will cause the minutes hand to keep running until button
(A) is released.
After setting the time manually, a date cannot be set.
In the display (C), a “1” is shown. This indicates that the watch is not cur-
rently set to the DCF.
The watch continuously tries to detect the DCF signal and will set itself au-
tomatically to DCF time if a signal can be obtained. This will be indicated
by a “0” in the reception status display, to the right of the seconds (see
“Display”).
DISPLAY
The date is normally shown in the display (C).
-
Press push-button (B) to display the seconds and the reception status. The
seconds are shown on the left and on the right, the days are displayed during
which no DCF reception was possible.
-
Press (B) again and wait a few seconds to return to the date display.
SETTING THE TIME ZONE
If you are outside the DCF time zone, you can set the time zone manually.
-
Briefl y press the push-button (A).
-
On the display, the current set hours are shown.
-
Press the button (A), until the correct hour is set. The hands run to the appropri-
ate position. The date will be automatically adjusted afterwards, if necessary.
-
To reset the time to DCF time, press and hold (A) for more than 3 seconds.
If the time has been set to a time zone outside the DCF time zone (+/- 1
hour), no automatic DCF synchronisation is performed and no manual DCF
reception is possible.
CHANGING BATTERIES
-
If “Lo” and the date fl ash in the display (C) and the second hand stops at the 12
o‘clock position, the battery must be replaced.
-
Replacing the battery should be done by a specialist, using special clockmaker
tools and professional knowledge.
-
To replace the battery, the back of the case is removed.
-
The battery can then be removed from its holder and be replaced.
RESTART AFTER BATTERY REPLACEMENT
-
After replacing the battery “H” will appear in the display (C).
-
Position the hour and minute hands to the 12 o‘clock position, as described in
“Positioning the hands”.
-
The watch now attempts a DCF reception and will set itself to the correct time,
after successful reception.
RESET
-
If the watch malfunctions, or it can no longer be operated, press and hold the
push-buttons (A) and (B) simultaneously for more than 3 seconds.
-
After releasing the buttons, the integrated microprocessor performs a reset. All
the settings are deleted and the display (C) shows “H”.
-
Now proceed as described in “Restart after Replacing the Battery”.
CLEANING AND MAINTENANCE
To clean the outside of the watch, a dry, soft, clean cloth is suffi cient. For heavier
soiling of the exterior, you can moisten the cloth slightly with lukewarm water.
Clean the watch very carefully; otherwise you may scratch it.
Do not press too heavily on the glass cover; this can lead to breakage.
SHOCK RESISTANCE
For normal use, the wristwatch is shock resistant. Nevertheless, do not expose the
device to extreme shocks such as might occur if the device falls onto a hard surface.
This may damage the clockwork or the position of the hands may be changed (Posi-
tioning the hands is described earlier in this manual).
WATER TIGHTNESS
Please take note of the labelling on the watch and its meaning.
Marking Suitability
none
The watch has to be protected against water.
3ATM
Washing your hands, rain, water spray
5ATM
see above + bathing, showering
10ATM
see above + swimming, snorkelling
20ATM
see above + free diving
DISPOSAL
a) Product
Electronic devices are recyclable waste materials and must not be disposed
of in the household waste!
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.
b) Batteries and Rechargeable Batteries
The end user is legally obliged (Battery Regulation) to return used batteries and
rechargeable batteries. Do not dispose of used batteries in the household waste!
Batteries/rechargeable batteries contain contaminants and are labelled with
the symbols you can see in the adjacent images to indicate that disposal
among domestic waste is forbidden. The symbols for the relevant heavy
metals are: Cd=cadmium, Hg=mercury, Pb=lead (the labelling is visible on
the battery/rechargeable battery e.g. under the refuse bin symbol shown on
the left).
You can dispose of your used batteries/rechargeable batteries free of
charge at your community‘s collection point or any place where batteries/
rechargeable batteries are sold!
You thereby fulfi l your statutory obligations and contribute to the protection of the
environment.
DECLARATION OF CONFORMITY (DOC)
The manufacturer hereby declares that this product conforms to the fundamental
requirements and the other relevant regulations of Directive 1999/5/EC.
You can fi
nd the Declaration of Conformity for this product at
www.conrad.com.
TECHNICAL DATA
Operating voltage:
3 V/DC (button cell CR1620)
Battery life:
approx. 2 years
