OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Cleaning & Changing the Belt
Assembling Your Vacuum Cleaner
Using the Attachments
1.
Place vacuum in its upright position.
Make sure that the vacuum cleaner
is
NOT
plugged into the electrical
outlet when adding or removing
accessories.
2.
Turn the carpet height selector
to the highest position and set the
Carpet to Floor selector to the
“Floor” position
.
3.
Remove the hose connector from
the rear of the unit and push in the
desired attachment firmly onto the
end of the hose.
4.
If additional length is required,
attach the extension tubes to the end
of the hose and then attach the
crevice tool, round brush or
upholstery brush to the end of the
extension tube.
10. Insert the left side of the agitator in
first by placing the end cap down
into the slot and then do the same
with the right side. Press firmly to
make sure that each end is
completely inserted.
11. Check to make sure that the belt is
centered on the pulley and that the
agitator turns freely.
12. Replace the top cover over the
power head base and lock in place
by turning the two screw locks
clockwise until you hear them lock
in place.
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
Note:
Do not plug the power cord
into an electrical outlet until
the vacuum is fully
assembled.
Handle Assembly
1. Carefully unpack all components,
set aside packaging.
2. Lift vacuum body to upright position.
3. Remove the screw (1) that comes
attached to the
body.
4. From the rear of
the vacuum, align
the handle with
groove and slide
onto vacuum. If
necessary, use
thumb and finger
pressure to slide
handle into position.
5. Once handle is in place, secure the
handle with the screws (2). (Fig. 1)
Caution:
Do not over tighten. Over
tightening could strip the screw holes.
Do not operate the vacuum without
the handle screws in place.
Fig. 1
Occasionally the power nozzle drive
belt will require changing, the
frequency will depend upon the amount
of use your vacuum sees.
1. Turn the vacuum "Off" and unplug
from power supply.
2. Turn the vacuum upside down on a
flat level surface.
3. With a coin or a thick flat head
screwdriver, unlock the two (2)
screw locks by turning counter-
clockwise. (Fig. 22)
Changing the Headlight Bulb
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
How to Start
The upright vacuum can be used on
multiple types of carpeting, bare floors or
upholstery with attachments. When using
the attachment tools such as the crevice
tool, round brush or the upholstery brush,
place the handle of the vacuum in the
upright position.
1. Turn the quick release cord holder
to either side 180° to release the
power cord.
2. Plug the power cord into the electrical
outlet.
3. Push the On/Off
button to the "On"
position to turn
the vacuum on.
4. To release the
handle, step
on the power
head and pull the handle back.
5. When using the attachments, the
vacuum must be in the upright
position. (Fig. 3)
Warning:
Avoid tipping the vacuum or
setting it on furniture, fringed area rugs or
carpeted stairs while you are using the
hose with the attachments. When using
the unit to vacuum floors or with
attachments, set the Carpet to Floor
Selector to the “Floor” position. This will
stop the beater brush from rotating. When
vacuuming carpets, avoid leaving the
vacuum in one place for an extended
period of time, particularly on thick carpet.
Caution:
Do
NOT
pull the vacuum
cleaner around the room by the hose as it
could tip over and cause damage. When
using the attachments, do
NOT
over
extend the hose length when reaching.
Trying to reach beyond the hose reach
could cause the vacuum to tip over.
Fig. 3
Fig. 22
1. Turn unit “Off” and unplug from wall
outlet.
2. With a flat head screw driver, snap
off the lens cover by pressing down
on the two notches on the lens
cover. (Fig. 24)
3. Lift off the head light lens.
4. Remove the bottom cover of the
power head.
5. Lift the right side of the agitator
brush first and then lift the left hand
side and lift the agitator brush out of
the power head.
6. Carefully remove any belt residue
that may exist in the belt area.
7. If the belt has broken, remove any
loose pieces before replacing with a
new belt.
8. Remove the worn or broken belt
from the motor drive shaft.
9 Loop the new belt first over the
motor drive shaft and then over the
agitator pulley. (Fig. 23)
Cord Assembly
1. Make sure that the quick release
cord holder is in the upright
position.
2. Remove the wire
tie from the power
cord.
3. Wrap the cord into
place by wrapping
it in a clockwise
direction around
the quick release
cord holder and
the lower cord
holders. (Fig. 2)
4. Turn the quick
release cord holder
to the left or to the right to unwrap
the power cord. (Fig. 2)
Warning:
Always make sure that the
vacuum is turned off
before unplugging.
Fig. 2
Notches
4. Remove the light bulb by pulling it
out carefully.
5. Replace the new bulb by pushing
it in.
6. Replace the head light lens by pushing
it in so that it snaps back in place.
Fig. 24
Insert
First
Fig. 23
4
9
