OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
The efficiency of your air driven
turbo brush depends on the
Bristle brush rotating at high
speed. Strong air suction is
needed to accomplish this.
In order to ensure that
maximum air suction is maintained, please
read the following instructions:
1. Empty the dust cup frequently.
2. Always shake out the dust cup filter
when emptying the dust cup container.
3. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.
4. Keep Air Driven Turbo Brush turbine
free of dirt and foreign matter. (See
page 6 for cleaning instructions.)
Air Driven Turbo Brush
1. Attach the flexible hose and the
extension tubes to the vacuum.
2. Attach the floor brush to the extension
tube.
3. You can use the floor brush with the
vacuum either with the caddy or as a
hand vacuum with the shoulder strap.
4. To vacuum bare floors, press the floor-
to-carpet lever on the floor brush down
to lower the bristles.
To vacuum carpets,
press the floor-to-
carpet lever up, to
raise the bristles.
Very flat carpets can
sometimes be vacuumed
with the bristles down.
Using the Floor Brush
1. To open the dust cup (container), push
the dust cup release button and pull
out the dust cup. Verify that the HEPA
dust cup filter is inside, then re-attach
the dust cup (container) to the hand
vacuum.
2. You have the option of using the Mini
Canister Vacuum as a hand held
vacuum or as a canister. To remove
the caddy from the main unit, press
down on the locking lever and lift the
unit up.
The Mini Canister Vacuum may be
used with the shoulder strap with or
without the caddy. To attach the
shoulder strap to the unit, attach the
hooks at the ends of the shoulder
strap to the shoulder strap
attachment points on the top of the
vacuum. See illustration below.
To replace the Mini Canister back
onto the caddy, slip the front part of
the unit onto the front locking tab of
the caddy (see below) and then lock
the unit in place by pushing it down
until the locking lever clicks in place.
The crevice tool that is provided with
the Mini Canister Vacuum can be
used either on the vacuum alone,
with the hose or with the extension
tubes. See illustration below.
Please note that the crevice tool will
only go in the suction hole of the
mini canister one way. See
illustration below. There is a detent
on the top of the crevice tool that
locks in place when inserted into the
suction hole. To remove the crevice
tool from the unit, press the hose
release button to allow you to
remove the accessory.
Warning:
Always unplug from electrical
outlet before opening the dust cup
(container).
Note
: HEPA dust cup filter must be used
when operating the hand vacuum.
Attaching the Shoulder Strap
Using the Flexible Hose
To use the flexible hose with the Mini
Canister Vacuum, push the end of
the hose into the suction hole as
shown below. The flexible hose may
be used with the deluxe brush,
crevice tool (see previous page),
floor brush or the air driven turbo
brush. To attach the flexible hose to
the unit, insert the hose end into the
suction hole making sure that the
detent is on the top. This will lock the
hose in place. To remove the hose,
press the hoe release button and
pull the hose out.
The extension tubes can also be
attached to the flexible hose to give
you a longer reach or to help
vacuum the floors with the floor
brush. Just push the wider end of
one of the tubes into the end of the
flexible hose and then attach the
other two tubes to each other. The
floor brush fits to the end of the
extension tubes.
Slide
Note:
The deluxe brush with
removable bristles can be used with
the hose or the extension tube.
For vacuuming high, hard to reach
places such as ceilings,
curtains/drapes, etc., use the
convertible brush with removable
bristles as follows:
1. Insert the convertible brush to the
hose alone or with the extension
tube attached to the hose.
2. If you need a brush action, slide on
the removable bristle brush onto the
deluxe brush. (See illustration
below.)
Using the Deluxe Brush with
Removable Bristles
Using The Unit As A Hand
Vacuum
Using the Crevice Tool
Using The Unit With Air Driven
Turbo Brush
1. Slide the narrow end of the extension
tube into the
air driven turbo brush
or the flexible hose
.
2. Slide the wide end of the assembled
extension tube onto the round end
of the deluxe hose.
3. Slide the round side of the hose into
the suction hole of the vacuum unit.
4. You can use the mini canister with or
without the shoulder strap.
5. You can now proceed to vacuum
your upholstery.
5
4
