Eudora GSI 6104 Manual Download Page 6

Page: 6 / 24

1234567890

TABLE OF WASH PROGRAMMES (display version)

ah c

les

Cyc

le n

umber

Rinse

Rapid 40º C

ECO 45º C

Normal 55º C
(EN 50242)

Intensive 65º C

(Optional)
Rapid 30º C

OFF

pre-wash

wash

Dishes

and

degree of dirt

Pans and dishes until
the next wash cycle

Little dirty dishes

Very dirty delicate dishes

Normally dirty dishes

Very dirty dishes (except
delicate pieces)

Little dirty dishes

Short cold wash to prevent food residue from
drying up and forming crusts on the dishes

Main wash
2 rinses (1 cold – 1 warm)

1 cold pre-wash - Main wash
2 rinses (1 cold – 1 warm)

1 cold pre-wash – Main wash
2 rinses (2 cold – 1 warm)

1 warm Pre-wash – Main wash
3 rinses (2 cold – 1 warm)

Main wash
2 rinses warm

Cycle

description

BUTTONS

DETERGENT

TABLE OF ERROR CODES

Action to be taken

- Reset the dishwasher
- Check
- Reset the dishwasher
- Verify the water pressure

Checks to carry out

- Tap closed
- Filter of loading tube blocked
- Water supply tube bent
- Insufficient water pressure

When this occurs

At the beginning

of the cycle

Error

LED 4

N.B.: Anomalies are signalled in the following way:
A continuous beep sounds until the programme with the error is reset.

N.B.: Upon contacting the authorised technical assistance centre always communicate the type of error
encountered.

Options

NOTE: All the options must be set after selecting one of the programmes.

• Delayed start (Delay)

This button is used to set a delay time between 1 and 12 hours. The first time the button is pressed the function is activated

and the display shows the delayed start symbol ( ), while the text “1H” is displayed in the numerical area. Each subsequent press of the button increases
the delay time by 1 hour, up to a maximum of 12 hours. The next press of the button deactivates the function; the “clock” symbol disappears and the duration
of the selected programme reappears in the numerical area. Once the delay time has been set, close the dishwasher door and press the start button (if
necessary); the delay time countdown will begin and the clock symbol will begin to flash until the selected programme begins. Until the programme begins, the
Display will show the remaining time when the door is opened.
To deactivate the delay, RESET the machine.

• Quick wash (IF APPLICABLE):
The “QUICK WASH

( )

symbol appears on the display when the button is pressed. At this point the machine is ready to start the wash programme.

• Half load (IF APPLICABLE):
The “1/2 LOAD” option is deactivated by default and the machine therefore washes loads on both upper and lower racks. If the “1/2 LOAD” button is pressed
once the wash will be performed using the upper rack only (this will be indicated by the corresponding
symbol on the display,

( )

If the button is pressed again the wash will be performed on the lower rack only and the lower rack symbol

( )

will be shown.

If the button is pressed once more the “1/2 LOAD” function will be deactivated. The “1/2 LOAD” function may be activated with all programmes and is
deactivated at the end of the programme.
NOTE: When the half load function is activated the duration of the wash cycle is reduced.

•

3 in 1 FUNCTION: Press and hold button

QUICK WASH (or 1/2 LOAD if provided) for 5 seconds; the “3 in 1” function is activated, a confirmation beep

is emitted and the tablet symbol ( ). is shown on the display. This function remains active for all programmes, until it is deactivated by pressing button

for

5 seconds, when the tablet symbol disappears from the display.
The use of combined detergents (such as 3 in 1 tablets or similar products) may remove the need for rinse aid and salt. The “3 in 1” function may be activated for
all programmes; the rinse aid indicator light is deactivated.
N.B. It is good practice to follow the instructions given on the container for the products mentioned above.
- Up to a water hardness of 21° dH (37° f) it is not necessary to use salt; set the regeneration adjustment to D1 (see paragraph entitled “adjusting the water
softening system”).
- Where water hardness is greater than 21° dH (37° f), salt must be used.
In this case fill the salt compartment and adjust the regeneration system to position D3.
Advice: Superior washing results can be achieved with the use of traditional detergents combined with salt and rinse aid.
WARNING: When traditional detergents are used the water softening system must be adjusted accordingly.