manualshive.com logo in svg

EUCHNER CES-AZ-ALS Series, Operating Instructions Manual, Page: 17 / 52

Share
Download
EUCHNER CES-AZ-ALS Series Operating Instructions Manual Download Page 17

17

2105274-12-08/20 (Translation of the original operating instructions)

Operating instructions

Non-Contact Safety System CES-AZ-UES-…

EN

 -Parameter setting operation starts (STATE LED flashes at approx. 1 Hz)

 -Wait for acknowledgment of the parameter setting operation (STATE LED goes out after approx. 10 seconds)

5.  End parameter setting operation

 -Remove jumper between J1 and J2 (for CES-AZ-UES-01B between J and 0V)

 -For operating mode 

Manual start

: start button must be connected

 -For operating mode 

with feedback loop

: feedback loop must be connected

 -Press reset button or interrupt operating voltage for at least 10 seconds

 -Wait for self-test (STATE LED flashes for approx. 10 seconds at 15 Hz)

6.  Check all guards for effectiveness

9.2.1.  Changing the configuration

The evaluation unit can be re-configured as often as required. For this purpose you must proceed as per the first parameter 

setting operation according to the section 

9.2. Parameter setting on page 16

.

Faulty actuators can be replaced. The number of parameter setting operations is unlimited.

Summary of Contents for CES-AZ-ALS Series





















































Reviews:

No comments