manualshive.com logo in svg

EUCHNER CES-AZ-ALS Series, Operating Instructions Manual, Page: 13 / 52

Share
Download
EUCHNER CES-AZ-ALS Series Operating Instructions Manual Download Page 13

13

2105274-12-08/20 (Translation of the original operating instructions)

Operating instructions

Non-Contact Safety System CES-AZ-UES-…

EN

8.4.  Connection example for CES-AZ-UES-01B

24 VDC

GND

-F1

0V

TST

-F2

UB

CES-AZ-UES-01B
105139

J

SH1

O1

Read-

head

1

H11

Trans-

ponder

H12

EUCHNER

-V1

DIA

-K3

A1

A2

23 24

-V2

13 14

-K4

A1

A2

feedback loop

Y1

Y2

-K4

21

22

-K3

21

22

S

Start

L1

-K3

13

14

-K4

13

14

M

3

~

-M1

L2

23

24

 23

24

L3

33

34

33

34

K2

+

K1

+

Important!

To achieve category  4 according to EN ISO 13849-1, it is necessary to monitor the downstream 

contactors (here: contacts on -K3 and -K4 in the feedback loop).
This example shows only an excerpt that is relevant for the connection of the CES system. The example 

illustrated here does not show complete system planning. The user is responsible for safe integration 

into the overall system.

If only one enable path is to be used for control (e.g. of downstream contactors), failures involving a short circuit between 

the contacts on the enable path and, for example, the power supply must be excluded.
With reference to EN ISO 13849-2 Table D.5, this exclusion can be provided if

 

Ì

the cables are inside an electrical installation space and

 

Ì

the enclosure meets the related requirements (see EN 60204-1 or IEC 60204-1).

Summary of Contents for CES-AZ-ALS Series





















































Reviews:

No comments