EUCHNER 097075 Operating Instructions Manual Download Page 7

Page: 7 / 44

2097098-18-10/19 (Translation of the original operating instructions)

Operating instructions

Non-Contact Safety System CES-A-UEA-02B/CES-A-UEA-04B

4. Exclusion of liability and warranty

In case of failure to comply with the conditions for correct use stated above, or if the safety regulations are not followed,

or if any servicing is not performed as required, liability will be excluded and the warranty void.

5. General safety precautions

WARNING

Danger to life due to improper installation or due to bypassing (tampering). Safety components fulfill

a personnel protection function.

Safety components must not be bypassed, turned away, removed or otherwise rendered ineffec-

tive. On this topic pay attention in particular to the measures for reducing the possibility of bypass-

ing according to EN ISO 14119:2013, section 7.

The switching operation must be triggered only by actuators designated for this purpose.

Mounting, electrical connection and setup only by authorized personnel possessing the following

knowledge:

-specialist knowledge in handling safety components

-knowledge about the applicable EMC regulations

-knowledge about the applicable regulations on operational safety and accident prevention.

The number of parameter setting and switching operations is saved in the internal memory of the

evaluation unit. If necessary, this memory can be read by the manufacturer.

Important!

Prior to use, read the operating instructions and keep these in a safe place. Ensure the operating

instructions are always available during mounting, setup and servicing. For this reason you should

archive a printed copy of the operating instructions. You can download the operating instructions from

www.euchner.com.

Summary of Contents for 097075













































Search results

Summary of Contents for 097075

Reviews:

Related manuals for 097075

Brands by name

Popular brands

EUCHNER 097075, Operating Instructions Manual

Search results

Summary of Contents for 097075

Reviews:

Related manuals for 097075

Brands by name

Popular brands