background image

System Installation

10

Terminate Wiring

Wire terminations are made to the terminals located on the back side of the fixture.

Step 1:

Locate the provided fixture termination kit.

Step 2:

Connect ground.

a: Locate the pre-stripped black wire with spade terminal.

b: Loosen but do not remove the GND terminal screw on the back of the fixture.

c: Insert the spade terminal under the screw and tighten the screw firmly to secure.

d: Locate a 3 position WAGO inside the termination kit and open all terminal levers.

e: Insert the pre-stripped end of the pigtail into a terminal and close the lever.

f: Strip the ground wire from the power supply to .35-.39” (9-10mm), then insert it 

into a terminal and close the lever.

g: If continuing to another fixture in the run, strip the wire .35-.39” (9-10mm) and 

insert it into the third terminal and close the lever.

Step 3:

Connect power.

a: Locate the pre-stripped red wire inside of the termination kit.

b: Loosen but do not remove the PWR terminal screw on the back of the fixture.

c: Insert the spade terminal under the screw and tighten the screw firmly to secure.

d: Locate a 5 position WAGO inside the termination kit and open all terminal levers.

e: Insert the pre-stripped end of the pigtail into a terminal and close the lever.

f: Strip the power wire from the power supply .35-.39” (9-10mm), then insert it into 

a terminal and close the lever.

g: If continuing to another fixture in the run, strip the wire .35-.39” (9-10mm) and 

insert it into the third terminal and close the lever.

Note:

It is acceptable to continue the wiring run for up to 10 fixtures per zone on a power 

supply. 

Dry Locaons Only

optio

nal C

TRL wi

re

pre-s

tripped

 PWR wire

from po

wer suppl

y

to 

the next f

ixture

  

Summary of Contents for GDS BluesSystem





























Reviews: