manualshive.com logo in svg

eta SH Touch, Operation Manual, Page: 45 / 64

Share
Download
eta SH Touch Operation Manual Download Page 45

45

2012-11

Log boiler [Boiler] 

Overview, buttons, functions

SH Operation

switched off because the control system assumes 
that the log boiler is to be started up. A correspon-
ding message is displayed.

Malfunction

There is a malfunction in the draught fan, the 
exhaust gas temperature sensor or the boiler 
temperature sensor. 

The boiler may not be 

started up in this mode.

Calibrating lambda probe

After every 500 hours of full-load operation, 
the boiler performs an automatic calibration of 
the lambda probe. This always occurs after an 
ember burnout and only at night between 23:00 
and 04:00. This calibration can also be initiated 
manually by opening the primary and secondary 
air valves and flushing the boiler with fresh air 
using the draught fan. If the boiler has not been 
started up for over 48 hours, this calibration takes 
only 30 minutes. If the boiler was in operation 
until recently, the calibration can take up to 3 
hours. If the boiler is started up during calibration, 
the calibration is aborted and started again 9 days 
later. 

Insulation door open

The insulation door is open. If the boiler was previ-
ously in heating mode, it switches back to heating 
mode after the insulation door is closed. For all 
other modes, the boiler switches to ignite mode 
after "Insulation door open". If the insulation door 
stays open for more than 30 minutes, an error 
message is displayed and (depending on setting) 
an audible signal emitted.

Overtemperature

The boiler temperature is over the temperature 
of 90°C set for [Boiler max]. The draught fan is 
switched off and an error message indicates that 
less fuel should be added in future. Once the boiler 
has cooled below 86°C, the draught fan switches 
on again and heating resumes.

TWIN in operation

This is only displayed if a TWIN burner (pellets) is 
installed on the log boiler.
"TWIN in operation" mode displayed as soon as the 
buffer needs heat and the log boiler is unable to 
provide it. Then the control system starts the TWIN 
burner to supply heat to the buffer. The current 
status of the TWIN burner is shown in the [TWIN] 
FUB.
If the log boiler's insulation door is open for more 
than 1 minute, the TWIN burner is automatically 

Summary of Contents for SH Touch

































































Reviews:

No comments