background image

44

www.eta.co.at

Subject to change due to technical improvements

Registering the touchscreen 

Remote control

Registering the touchscreen

Once you have entered all your login data, press 

 to save the data.

t.mustermann

t-online.at

my...

xxxx-yyyyy-zzzzz

Registering the touch screen

Once you have pressed the 

 

button, the touch screen is registered at 
<www.meinETA.at>.

The 

 symbol appears at the bottom 

of the screen while the system is establishing an 
Internet connection.

 If the system is unable to establish an Internet 

connection, check that the login data you have 
provided is correct.

Internet connection status

After a delay of about 15 seconds, the screen 
displays the current status of the Internet 
connection.

 Connecting

This symbol is displayed while the touch screen 
is establishing an Internet connection, during 
registration or after remote control has been 
switched on.

 Connected

The touch screen has an active Internet connection 
to the homepage <www.meinETA.at>. The boiler 
can be controlled remotely.

 No connection possible

The touch screen is not currently connected to the 
Internet. If this symbol is still being displayed after 
one minute, there is a fault in the access cable, 
with your Internet service provider or with the 
meinETA server.

In order to locate the fault, it may help to test the 
network connection by connecting a laptop to the 
network instead of the boiler. 

Summary of Contents for PE-K 35





























































Reviews: