ESM F - 4u Corsair Instruction Manual Download Page 8

1

Stab joiner (12x290mm)

6

2

Pin hinge(2.5x48mm)

Steel wire (0.5x3000mm)

1

U-style wire (150x25x3mm)

4

Matal douel (4x30mm)

1

Rib template (2mm ply)

2
2

2

Clevis

Copper joiner

Aluminum tube(3x6mm)

2

2

Screw  (2x10mm)  

Nut (2mm )

2

Washer(2x5mm)

Drill  two holes for pulling out the servo extension line.

Center

   line 

 25mm 

 100mm 

10mm

Pleas clear the appropiate position before epoxy the

plies in it.

1

 Wooden Block (2mm Ply)

 Wooden Block (2mm Ply)

Drill two holes to relevant position in the fuselage

Mount the wings to the fuselage with screw .

8mm

120 mm

120 mm

2

Wood dowel  (8x50mm)

32mm

32mm

8mm

6.2mm

Blind Nut

2

2

Blind Nut (6mm)

Screw(6x50mm)

Trim the surplus section from the wheel door and make 

sure the retract system can retract into the wings 

accurately when the gear up.

Drill two holes to appropriate position in the leading 

edge of the center wing and mount the wood dowels 

in them.

6

32

30

28

30

29

Accessory list for the coming installation steps.

31

Fuel supply line

Fuel spray line

Air pressure line

6.2mm

Blind Nut

4

Blind Nut (5mm)

Washer 

Screw 

Washer

Assembly of  the fuel tank.

Drill four holes at the diameters as shown for engine 

mount.

Assemble the engine.

In case of 2-cycle & 4-cycle engine.

180 mm

The front view of the engine install completion.

Engine mount is a movable cylinder.

Epoxy the fuel tank to the fuselage.

The side view when the engine install completion,

customers can adjust the engine position by move 

the engine mount.

11

60

58

55

56

57

59

Summary of Contents for F - 4u Corsair











Reviews: