ESM F - 4u Corsair Instruction Manual Download Page 10

4
4
4

Clevis

Copper joiner

Aluminum tube(3x6mm)

4

4

Screw  (2x10mm)  

Nut (2mm )

4

Washer(2x5mm)

C

C’

D

D’

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and 

check its correct position.

Securely glue together.If coming off during flights,

you'll lose  control of your airplane which leads 

to accidents!

C = C '

D = D '

4

Steel wire (0.5x3000mm)

Steel wire (0.5x3000mm)

2

Pin hinge(4.5x67mm)

8

TP Screw (2.3x12mm)

Ply (15x15x3mm)

8

1
1

Collar (3mm)

Metal wire for rudder 

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

2
2

2

Clevis

Copper joiner

Aluminum tube(3x6mm)

2
2

Screw  (2x10mm)  

Nut (2mm )

2

Washer(2x5mm)

Steel wire

Copper joiner

Aluminum tube

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Install the elevator servo.

2

Wheel (45mm)

Wheel (45mm)

2

Steel wire (0.5x3000mm)

Epoxy the tail retract to the former in the fuselage and 

connect the steel wires as illustration.

1

1

Air line (3000mm)

1

Ply(3mm) 

wheel  mount servo.

Note:rubber wheels oleo struts 

and retracts are optional.

Assembly of the stabilizer.

Assemble the elevator servo to appropriate position in 

the fuselage.

Epoxy the elevator to the stabilizer.

8

43

40

42

Accessory list for the coming installation steps.

39

41

5x16mm

1x20mm

4
4

4

Clevis

Copper joiner

Aluminum tube(3x6mm)

4
4

Screw  (2x10mm)  

Nut (2mm )

4

Washer(2x5mm)

Steel wire

Copper joiner

Aluminum tube

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Install the rudder servo.

2

Steel wire (0.5x3000mm)

Collar (3mm)

Steel wire (0.5x3000mm)

93mm

Elevator servo

Rudder servo

Put the frame in the rudder metal wire.

Trim slots in appropriate position to the tail fuselage as 

illustration and epoxy the rudder metal wire to the slot 

in the fin

Epoxy the frame to the appropriate position in the 

fuselage and fix it to the metal wire with collar.

The sketch map of all the steel wires pass the 

former in the fuselage.

Assemble the rudder servo to appropriate position in 

the fuselage.

9

49

48

47

44

45

46

Summary of Contents for F - 4u Corsair











Reviews: