background image

Technical Data 

 

 

ECS-CPCIs/FPGA

  

 Hardware Manual Doc.-Nr.: E.1108.21/ 1.0 

Page 21 of 28 

 

 

Number 

Standard 

100BASE-TX, 100Mbit/s according to IEEE 802.3 

Controller 

EtherCAT Slave Controller Beckhoff IP Core integrated in FPGA  
+ 2x MII Phy (Micrel KSZ8081MNX) 

Electrical isolation 

via transformer, integrated in RJ45 connectors 

Ports 

IN and OUT 

Connector 

2 x RJ45 socket with separate LEDs for status indication (see 

LED 

Indication

 page 16) 

 

Table 7:

 Data of the EtherCAT interface 

 

Number 

2 x Sync + 2 x Latch 

Electrical isolation 

none 

Voltage level and 
termination 

3.3V LVTTL configured as 4 single ended lines, no protection against 
electrostatic discharge or over voltage. 

The lines include a 33 Ω series 

resistors near to the FPGA. 
On customer request the lines can be modified as two differential 2,5V 
LVDS pairs (one sync and one latch function must be shifted to user I/O 
lines then). Ask our sales team (

[email protected]

) for further information. 

Controller 

Integrated in FPGA 

Connector 

High Speed/Modular Connector (all signals on P3) (For the pin assignment 
see chapter 

“P3 – 96-Pin Header configured for LVTTL I/O” on page 25.

 

Table 8:

 Data of SYNC/LATCH interface on P3 

 

Number 

32 User I/O 

Electrical isolation 

None 

Voltage Level and 
Termination 

3.3V LVTTL configured as single ended lines, no protection against 
electrostatic discharge or over voltage.  
16 lines include a 

33 Ω-series resistor near to the FPGA. On customer 

request these 16 lines can be modified as 8 differential 2,5V LVDS pairs. 
Ask our sales team (

[email protected]

) for further information. 

Controller 

Integrated in FPGA 

Power Supply 
Output 

3,3V/ 1A unprotected and 12V / 0,5A unprotected 

Connector 

High-Speed/Modular Connector (all signals on P3) (For the pin assignment 
see chapter 

“P3 – 96-Pin Header configured for LVTTL I/O” on page 25.

 

Table 9:

 Data of User-I/O interface on P3 

 

4.4 EtherCAT Interface 

4.5 SYNC / LATCH Interface on P3 

4.6 User-I/O on P3 

Summary of Contents for ECS-CPCIs/FPGA





























Reviews: