ESCO Technologies ETS-LINDGREN MAPS 2112 Series User Manual Download Page 17 | Manualshive

Page: 17 / 38

background image

17

SPECIFICATIONS

Electrical Specifications

Nominal AC Voltage:

208–230 VAC

Input Frequency:

50/60 Hz

Current Rating:

10 amp service

Phase:

Single

Physical Specifications

Unit Diameter:

160.02 cm (63 in)

Typical Turntable Platform Height:

36.96 cm (14.55 in)

Approximate Installed Unit Weight:

453.59 kg (1000 lb)

Mast Specifications

2112

2117

2122

Height:

Customer-specified

Maximum EUT Load

(within the area of the

provided mount):

0.45 kg (1 lb)

11.3 kg (25 lb)

34 kg (75 lb)

Note:

Contact your ETS-Lindgren sales representative for shipping container

dimensions and weight.

«
...
15
16
17
18
19
...
»

Summary of Contents for ETS-LINDGREN MAPS 2112 Series







































Reviews:

No comments

Related manuals for ETS-LINDGREN MAPS 2112 Series

DAC RE 3581 Series

Brand: RTK Pages: 25

Brand: P.A. Pages: 8

Brand: cascade corporation Pages: 24

Brand: Beko Pages: 24

Brand: Parker Pages: 36

Brand: Incra Pages: 16

Brand: Will Burt Pages: 68

Brand: PS Automation Pages: 4

Brand: Aventics Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands