background image

227

To  connect  PT-21AMX  torch  to  the  console,  connect  the  power  cable  of  the 

torch to the ‘‘NEG’’ terminal and pilot arc cable to the ‘‘POS’’ terminal of the unit 

using pilot arc adaptor (p/n 19497 (4485843) - supplied with spare parts kit). A 

separate  remote  control  switch  cable  is  required  for  connecting  to  the  switch 

receptacle on the console.

The  front  end  of  the  torch  contains  a  gas  flow  check  valve  that  acts  in 

conjunction  with  the  circuitry  provided  in  the  power  supply.  This  patented 

system provides a safety interlock preventing the torch from being accidentally 

energized  with  high  voltage  when  the  heat  shield  is  removed  and  the  torch 
switch is accidentally closed.

 

6.    Tighten heat shield fully to hold the parts in firm contact with each other and 

to the torch head. “Fully” means at least 3/16" (4.8mm)  rotation after electrode 

seat contacts electrode holder.

5.    Apply a thin film of lubricant p/n 17672 (0558000443)  to O-ring p/n 488157 

(4485841).

4.    Install  nozzle  onto  the  electrode  assembly  by  inserting  small  shoulder  on 

electrode  insulator  into  nozzle’s  rear  opening.  Place  nozzle  and  electrode 

assembly into the heat shield. If front end of the torch is facing down as normal 

in a setup, the nozzle and electrode assembly can be stacked in the heat shield 

and then assembled to the torch. Be sure to use proper heat shield and nozzle 

combination.

O-ring 

Lubricant 

(NOTE:  Part numbers in parenthesis  apply 

to "CE"/European units only.)

SECTION 3 

OPErATION

Summary of Contents for POWERCUT-1250













































Reviews: