Erie water treatment IQsoft, Technical Manual

Page: 10 / 28

ELECTRONIC CONTROL PANEL
Page 10
12. Press the scroll  button again; the display will show:
•
Press the up  or down  button to set the salt level
alarm interval (= number of regens after which the salt
level alarm is activated)
.
13.
Press the scroll  button again; the display will show
(only when the regeneration mode was set to 'Dlyd' or
'Dlyd/Immd'):
•
Press the up

or down

button to set the reserve
capacity :
−
Variable : the reserve capacity is calculated
automatically, based on the registered daily water
usage.
−
Fxd : press the scroll

button again and press the
up  or down  button to set the reserve
capacity to a fixed amount .
14.
Press the scroll

button again; the display will show:
•
Press the up  or down  button to set the function
of auxilliary contact 1 and auxiliary contact 2 :
−
Regen : aux. contact is powered during entire
regeneration (does not include refill and brine
preparation cycles!).
−
Chlor.Cell : aux. contact is powered at start of
brine draw/slow rinse cycle. Press the scroll 
button again and press the up

or down

button to set the duration of activation of the
chlorination cell .
−
Maintenance : aux. contact is powered when
maintenance reminder is triggered.
−
Error : aux. contact is powered when timer failure
occurs.
−
Light : aux. contact is powered when display
backlight is activated.
−
Salt alarm : aux. contact is powered when salt
level alarm is triggered.
15. Press the scroll  button again; the display will show:
•
Press the up

or down

button to save the settings
into the NOVRAM® and exit the programming mode.
DIAGNOSTICS MODE

In the Diagnostics mode several operating parameters
can be consulted; particularly during a service intervention,
these parameters can be helpful to identify the cause of a
problem or malfunction.

Before entering the Diagnostics mode, make sure that
the appliance is in service mode.

In case no button is pressed in a period of 5 min, the
control panel will automatically return to the service mode!
ACCESSING THE DIAGNOSTICS MODE
1. Press the scroll  button and hold it for 6 sec until the
display shows:
2. Within 10 sec, press the down  button; the display will
show:
•
You are now in the Diagnostics mode.
•
Press the scroll  button to advance to the next
diagnostics parameter.
AVAILABLE DIAGNOSTICS PARAMETERS
•
Regen X days ago : number of days since last
regeneration.
•
In Srvc : total number of days in service.
•
# of Regens : number of regenerations since installation.
•
TotVol : total volume of treated water since installation.
•
LastSet : number of days since last change of configuration
parameter or hardness of incoming untreated water.
•
InstFlow : instantaneous flow rate through appliance.
•
AvgVol : calculated average daily water usage.
•
LastRgn@ : consumed capacity at last regeneration.
•
Capacity : calculated capacity between regenerations.
•
TotAgeCorr : total accumulated age correction factor.
•
MaintCnt : current status of maintenance reminder
counter (counting up).
•
MP Resets : number of resets of microprocessor.
•
Memory Reset : number of corrupt memory start-ups.
•
CapToUse : remaining capacity.
•
Fill : length of refill cycle of last regeneration.
•
Alarm count : current status of salt level alarm counter
(counting up).
•
Reserve : calculated reserve capacity.
•
EZ2L4d EZ2LPBr13 : software version.
EXITING THE DIAGNOSTICS MODE
1. Press the scroll

button repeatedly until the display
shows:
•
Press the up  or down  button to exit the
Diagnostics mode.
Exit
Rsrv Variable
Alarm interval:
9 Regens
AUX: Regen
System Check
Regen XXdays ago
Exit