manualshive.com logo in svg

Ergofix ELECTRIC HEIGHT ADJUSTABLE TABLE, Assembly And Operation Instructions Manual

Share
Download
Ergofix ELECTRIC HEIGHT ADJUSTABLE TABLE Assembly And Operation Instructions Manual Download Page 12

Error Code Key

Code Meaning

Suggested Actions

E01

Power supply exceed input voltage 
range.

Check if power supply is within required input 
voltage range.

E02

Lift columns unbalanced by > 10mm.

Perform reset procedure.

E03

Handset not connected.

Plug handset wire connector into the control 
box.

E04

Handset communication error.

Check handset for damage. Reconnect handset 
wire connector into the control box.

E05

Obstacle detected, anti-collision 
activated.

Release depressed button.

E06

Start up error.

Reconnect all cable connectors into control box. 
If problem persists, check with technical 
support.

E07

Control system error.

Perform reset procedure.

E08

Table tilts during height adjustment.

Perform reset procedure.

E09

Overheated or duty cycle limit was 
reached.

Let the table electronics cool down for at least 
18 minutes before using.

E11/21

Motor M1/M2 is not connected.

Plug M1/M2 motor cable connectors into the 
control box.

E12/22

Motor M1/M2 current sampling error.

Reconnect M1/M2 motor cable connectors into 
control box. If problem persists, check with 
technical support.

E13/23

Phase loss or phase line disconnected 
from motor M1/M2.

Reconnect M1/M2 motor cable connectors into 
control box. If problem persists, check with 
technical support.

E14/24

Hall sensor error or hall sensor wire 
disconnected from motor M1/M2.

Reconnect M1/M2 motor cable connectors into 
control box. If problem persists, check with 
technical support.

E15/25

Motor M1/M2 internal circuit error.

Reconnect M1/M2 motor cable connectors into 
control box. If problem persists, check with 
technical support.

E16/26

Motor M1/M2 stalled.

Perform reset procedure.

E17/27

Motor M1/M2 directional error.

Reconnect M1/M2 motor cable connectors into 
control box. If problem persists, check with 
technical support.

E18/28

Table overloaded.

Reduce weight on the table.

OPERATION GUIDE

Summary of Contents for ELECTRIC HEIGHT ADJUSTABLE TABLE















Reviews:

No comments

Brands by name

Popular brands

Load more brands