SQUIDS
®
BARCODE
SCANNER BELT
WWW.ERGODYNE.COM // 800 225 8238
The Squids® Barcode Scanner Belt Hook Lanyard is designed for ease-of-use while
reducing the risk of dropped barcode scanners (refer to Using A Tethering System
instructions).
WARNINGS: ALL WARNINGS AND INSTRUCTIONS MUST BE READ AND UNDERSTOOD
BEFORE USING THIS PRODUCT. FAILURE TO DO SO MAY RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, OR DEATH.
• Never exceed the allowable weight capacity for any Tool Lanyard.
• Always inspect Tool Lanyard prior to, and after, each use (refer to INSPECTION
instructions).
• Do not wrap a Tool Lanyard around sharp or rough edges.
• Never modify or alter your Tool Lanyard.
• Never modify a tool that could result in manufacturer guideline deviation.
• Do not use this product if it interferes with the tool’s safe working condition.
• Use extra precaution around moving machinery or parts, electrical hazards, chemical
hazards or other apparent hazards.
INSTRUCTIONS FOR ATTACHING 3135 BARCODE SCANNER BELT HOOK LANYARD
TO BARCODE SCANNER
The 3135 barcode scanner belt hook lanyard is designed to be used with the 3136 barcode
scanner adaptor strap. Both are included with the 3135.
1. The 3136 barcode scanner adaptor strap attaches to the barcode scanner using the
two small loop attachments on the end of the modular female buckles. Detach the
female buckle ends from the rest of the barcode scanner adaptor strap for installation
[fig. 1]
2. Take the small loop attachment on the modular female buckle and thread it through
the captive hole in the bottom of the barcode scanner gun. [fig. 2]
- If necessary, use a small screwdriver or hex key to help thread the loop attachment
through the captive hole on the barcode scanner [fig. 3]
3. Cinch the loop attachment to the captive hole in the barcode scanner by pulling the
female buckle end through the loop and pulling the loop tight to remove slack. [fig. 4]
4. Repeat steps 2 and 3 using the captive hole located near the rear bottom of the
barcode scanner. Attaching both loop attachments provides extra barcode scanner
gun stability. [fig. 5].
INSTRUCTIONS FOR ATTACHING BARCODE SCANNER BELT HOOK LANYARD TO
BODY
1. Adjust the webbing strap on the barcode scanner belt hook for best fit. Clip the large
male and female buckles on the barcode scanner belt hook lanyard around the waist
to wear as a belt. [fig. 6]
2. To wear as a sling, place the barcode scanner belt hook lanyard over your head and
onto your right or left shoulder [fig. 7].
3. Hang the barcode scanner gun on the 3135 belt hook from the webbing on the 3136
barcode scanner adapter strap. The barcode scanner gun should rest near the hip for
optimal comfort [fig. 8].
AMBIDEXTROUS FUNCTION
The barcode scanner belt hook lanyard can easily be reconfigured for right- or left-handed
people. For right-handed users, align the belt hook near the right hip during use. For left-
handed users, align the belt hook near the left hip during use.
* For further instructions, watch the product video on www.ergodyne.com.
INSPECTING A BARCODE SCANNER BELT
Inspect a tethering system before and after each use. All equipment should be regularly
inspected by a competent person. Ensure the tethering system is properly attached to the
tool and is not damaged. Before each use, check the following:
• Examine webbing, stitching and other soft materials for cuts, tears, heat trauma, frays
or other damage.
STORAGE AND CARE
Store tool attachments in a clean, dry location, away from direct sunlight. Clean
attachments using mild soap and water, and then air dry.
DISCLAIMER
In no event, shall Tenacious Holdings, Inc., be liable for any direct, indirect, punitive,
incidental, special, or consequential damages arising out of, or associated with, the misuse
of Squids® tethering system components (tool lanyards or attachments).
WARRANTY
We stand behind everything we make and guarantee our products are free of defects in
materials and workmanship to the original purchaser for the product’s lifetime. Damage,
abuse, and/or normal wear are not covered. Questions? Call Ergodyne at +1-651-642-9889
(8 a.m. - 5 p.m. CST) or 800-225-8238.
El cordón de seguridad con gancho de cinturón Squids® se ha diseñado para facilitar el
uso del escáner de códigos de barras y reducir el riesgo de que se caiga (consulte las
instrucciones sobre Cómo utilizar un sistema de sujeción).
ADVERTENCIAS: ANTES DE UTILIZAR ESTE PRODUCTO, DEBE LEER
ATENTAMENTE TODAS LAS ADVERTENCIAS E INSTRUCCIONES. SI NO LO HACE,
PODRÍA DAÑAR EL MATERIAL Y SE PODRÍAN PRODUCIR LESIONES GRAVES O
INCLUSO LA MUERTE.
• No se debe exceder nunca el peso máximo permitido de ningún cordón de seguridad
para herramientas.
SPANISH // ESPAÑOL
FIG. 1
FIG. 2
FIG. 3
FIG. 4
FIG. 5
FIG. 7
FIG. 6
FIG. 8
