2. Turn the speed dial (5) anti-clockwise to decrease the maximum speed. A lower
setting is suitable for sanding with coarse-grained sanding papers to remove
paints and varnishes.
Operation
WARNING! Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative).
Materials containing
asbestos may only be worked by specialists. Use a dust extraction
system suitable for the material as far as possible.
01
Sanding
• Do not use the same sanding paper on different materials, e. g. do not use the
sanding paper that has been used for sanding metal to sand wood. Small metal
particles remaining in the sanding paper will lead to scratches.
• Ensure the workpiece is free of obstacles like nails or screws before operation.
Remove them if required. Where possible, secure smaller workpieces to prevent
them from moving under the product.
• Hold the product with one hand on the front hand grip (1) and with the other hand
on the main handle (4).
• Switch the product on and wait until it runs at full speed before placing it on the
workpiece.
• Move the product slowly and steadily over the workpiece surface in parallel and
overlapping stokes.
• Only apply the least possible pressure to keep the product flat on the workpiece.
Higher pressure will not increase but lower the performance of the product,
increase wear of the sanding paper and lead to uneven results.
• Work with a dust extraction system particularly when sanding coats of varnish as
the varnish could melt and smear the surface of the workpiece and the sanding
paper.
• Keep the product moving at all times, do not stop in one position to avoid grooves.
• Lift the product from the workpiece before switching it off.
After use
• Switch the product off, wait for complete stop, disconnect it from the power supply
and let it cool down.
• Check, clean and store the product as described below.
Use
Intended use
This product is intended for dry sanding of wood, plastic, metal, fillers and coated
surfaces. This product should not be used on other materials or those harmful to
health.
Before you start
01
Protection
Controls
01
On/Off switch & Lock-on button (Fig. K)
Operate the product either in instant or continuous mode.
Instant mode
1. Switch the product on by pressing the on/off switch (2). The oscillation speed can
be controlled by the pressing depth. Release the trigger to stop the power tool.
Continuous mode
1. Switch the product on by pressing the on/off switch (2) and hold it in position.
2. Press the lock-on button (3) to lock the on/off switch (2).
3. Release both switches. The on/off switch (2) is now locked-on for continuous use.
4. Depress and release the on/off switch (2) to switch the product off.
02
Speed dial (Fig. K)
Limit the maximum speed using the speed dial (5).
1. Turn the speed dial (5) clockwise to increase the maximum speed. A higher setting
is suitable for sanding with fine-grained sanding papers to achieve a fine finish.
21
20
Summary of Contents for 3663602796794
Page 1: ...EHSS350 EAN 3663602796794 ORIGINAL INSTRUCTIONS MNL_EHSS350_V03_BX220IM 10 8 2020...
Page 4: ...Product description 1 6 1 4 2 3 5 7 8 8a 13 9a 9a 9 10b 10b 10 10a 11 12 4...
Page 5: ...A 7 12 B 8 8a 8 8a C D 8 12 8 8 12 8a E F 11 6 10 5...
Page 6: ...G 1 2 3 G 10b 10b 1 2 1 2 H 10a 10c I J 1 2 9 6 9a 9a 9 2 1 1 K 5 3 2 1 2 6...
