background image

Other Information

EQD                                                                       16                                                   EQ2688

Troubleshooting

Please contact EQD service team directly if you have questions, service needs, 

or require technical assistance related on the use of your television.

Problem

Possible Solution

No power

• Make sure the power cord is properly connected to the LCD 

TV AC power socket.

• Make sure the AC power cord is properly connected to the 

wall outlet.

• Make sure the DC power button is ON (Blue LED).

• Plug another electrical device (like a radio) to the power out-

let to verify that the outlet is supplying the proper voltage.

No picture

• The TV station may be experiencing problems. Try another 

channel.

• The Cable TV signal may be scrambled or encoded. Please 

contact your local cable operator.

• Make sure that connection to other components are correct 

referring to the user guide.

• Make sure that setup has been done correctly after connec-

tions.

• Make sure the correct input is selected and the input signal is 

compatible.

Strange color, light color, or color

misalignment

• Ensure that the video cable is securely connected.

• The picture may appear dim in a brightly lit room.

• Adjust brightness, contrast, saturation (color), and tint referring 

to the user guide.

• Check the input signal setting.

Unit cannot be operated

• External influences such as lightning or static electricity may 

cause improper operation. In this case, operate the unit after 

first turning on the power of the LCD TV and the AVC System, 

or unplug the AC cord for 1 to 2 minutes, then plug in again.

No sound

• Check your audio connections are properly connected refer-

ring to the user guide.

• The MUTE button may have been pressed, try pressing this but-

ton again.

• Check your audio settings, your TV audio may be set to mini-

mum.

• Press the (Up) button on the remote control.

Remote control unit does not operate

• Make sure the directions of batteries are inserted correctly 

referring to the user guide.

• Batteries could be weak or dead. Replace with new batteries.

• Is a fluorescent light illuminated near the remote control sen-

sor?

• The path of the remote control beam may be blocked. Make 

sure the path is clear and that the remote control is aimed at 

the remote control sensor on the TV.

• Press the POWER button on the remote control to see if you 

can turn on the TV.

• Press MENU button on the remote control to see if there is a 

MENU shown on the screen.

• Press only one button at a time and it is the correct one for the 

operation you want to perform.

Picture is cut off/with sidebar screen

• Is the image positioned correctly?

• Are screen mode adjustments such as picture size set cor-

rectly?

• Press WIDE button repeatedly on the remote control to see if 

you can get the picture you prefer.

Power is cut off suddenly

• Is the sleep timer set in advance?

• Is there no signal in PC mode or HDMI mode?

• The internal temperature of the unit has increased. Remove 

any objects blocking the vent or clean as necessary.

No CATV reception (or no reception above CH13)

• Is the AIR/CABLE option set correctly? Please set the AIR/

CABLE option to CABLE referring to the user guide.

• CATV is connected improperly or not connected; please 

check all the CATV connections.

• The cable TV service is interrupted; please contact your cable 

operator.

Summary of Contents for Auria EQ2688


























Reviews: