manualshive.com logo in svg

Epson Stylus Photo R290, Service Manual, Page: 92 / 125

Share
Download
Epson Stylus Photo R290 Service Manual Download Page 92

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.4.17 Front Paper Guide Assy (Disassembling the Printer Mechanism)

92

4.4.17  Front Paper Guide Assy

†

Parts/Components need to be removed in advance

Printer Cover / Paper Support Assy / Upper Housing / Main Board Unit / Panel Assy / 
Cover Open Sensor / Printer Mechanism / Ink System / CR Motor / PF Encoder / PF 
Scale / PF Motor / EJ Frame Assy / APG Unit / CR Unit / ASF Unit / Upper Paper 
Guide

†

Removal procedure

1.

Remove the screw and remove the Parallelism Bushing L.

•

Screw

: C.B.S.(P2) M3x8 (tightening torque: 6-8 kgf.cm) 

(No.9)

Figure 4-107.  Removing the Parallelism Bushing L

2.

Disconnect the connector of the PE Sensor Cable on the rear side of the 
printer.

3.

Remove the screw that secures the Front Paper Guide Assy.

•

Screw

: C.B.S. M3x6 (tightening torque: 7-9 kgf.cm) 

(No.1)

Figure 4-108.  Removing the PE Sensor Cable

4.

Pull out the EJ Ground Spring to the front side.

Figure 4-109.  Removing the EJ Ground Spring

C A U T I O N

Do not touch the surface of the rubber roller of the EJ Roller Assy 
and the coated part of the PF Roller Assy as it can adversely affect 
the print quality.

Parallelism Bushing L

Front Paper Guide Assy

[Rear Side]

Positioning Hole and Guide Pin

PE Sensor Cable

Connector

Front Paper Guide Assy

Front Paper Guide Assy

EJ Ground Spring

Summary of Contents for Stylus Photo R290






























































































































Reviews:

No comments