manualshive.com logo in svg

Epson Stylus Photo R290, Service Manual, Page: 107 / 125

Share
Download
Epson Stylus Photo R290 Service Manual Download Page 107

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 5 Adjustment

5.3  Banding Reduction System (BRS) Adjustment / Paper Feed Amount Profile (PFP) Correction

107

5.3  Banding Reduction System (BRS) Adjustment / 

Paper Feed Amount Profile (PFP) Correction

5.3.1  Overview

This section explains how to carry out BRS/PFP adjustments.

†

Tools and paper required to perform the adjustment

†

Specified Scanner to perform the adjustment

The following are the scanners that can be used for scanning the pattern in BRS/PFP 
adjustment. When starting up the adjustment program, select the scanner to use. 

Figure 5-11.  System Configuration

C H E C K

P O I N T

„

For overview of BRS/PFP Adjustment,

 

refer to Chapter 2

 

“2.3 

Banding Reduction System (BRS) / Paper Feed Amount Profile 
Correction (PFP) 

(p.26)

„

Be sure to have a specified scanner ready beforehand as it is 
necessary to carry out the adjustment. Before scanning, 
confirm that the document table is free from any dirt or stain. 

Table 5-6.  Tools and Paper for BRS/PFP Adjustment

Tools/Paper 

Product Code

Common

PFP Base scale

1453980

BRS

Matte Paper-Heavyweight

(A4)

---

PFP

Premium Glossy Photo Paper

(4 x 6)

---

C A U T I O N

„

Install the driver of the scanner to the PC in advance. 

„

As the profile required for the adjustment is not prepared for 
scanners other than the ones specified below, BRS/PFP 
Adjustment can not be carried out by the other scanners. 

Table 5-7.  Specified Scanner for BRS/PFP Adjustment

Model Name

Sensor type

Remarks

Perfection 4990 Photo

CCD

Perfection V700 Photo

CCD

Stylus Photo RX560/RX580/RX590 CIS

Use the internal scanner.

Stylus Photo RX585/RX595/RX610 CIS

Use the internal scanner.

Stylus Photo RX680/RX685/RX690 CIS

Use the internal scanner.

C H E C K

P O I N T

Depending on the sensor type of the scanner to use for the 
adjustment, drying time required after the BRS adjustment 
pattern has been printed differs. For PFP adjustment pattern/PFP 
check pattern, drying time is not required. 

„

For “CCD” sensor:
Printed pattern can be scanned straight away. (Drying time of 
about 2 minutes is recommended.)

„

For “CIS” sensor:
Printed pattern needs to be dried more than 5 minutes. 

Calculate 

correction 

value

Test Pattern

Scanner

PC

Printer

Summary of Contents for Stylus Photo R290






























































































































Reviews:

No comments