manualshive.com logo in svg

Epson Stylus Photo R290, Service Manual, Page: 40 / 125

Share
Download
Epson Stylus Photo R290 Service Manual Download Page 40

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3  Troubleshooting by Error Message

40

Table 3-10.  Troubleshooting for CD-R Tray Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

When printing on 
CDs/DVDs

The CDR Tray is set to the printer, 
but the error occurs.

CDR Tray

1. Has the part of the CDR Tray that contacts with 

the CDR Tray Sensor become cracked? 

1. Replace the CDR Tray.

-

CDR Tray Sensor

1. Is the CDR Sensor cable not connected to CN4 on 

the Main Board?

1. Connect the cable to the connector on 

the Main Board.

4.4.18 “CDR 
Tray 
Sensor”(p.94)

 / 

4.3.1 “Main 
Board 
Unit”(p.61)

2. Is the CDR Tray Sensor damaged?

2. Replace the CDR Tray Sensor.

The CDR Tray center detection 
sequence is interrupted, and the tray 
is ejected.

CDR Tray

1. Is there any paper dust or foreign matter on the 

white mark on the CDR Tray?

1. Remove any dust or foreign matter from 

the tray.

-

CDR Tray

Contact point

White Mark

Summary of Contents for Stylus Photo R290






























































































































Reviews:

No comments