manualshive.com logo in svg

Epson Stylus Photo R290, Service Manual, Page: 31 / 125

Share
Download
Epson Stylus Photo R290 Service Manual Download Page 31

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 3 Troubleshooting

3.3  Troubleshooting by Error Message

31

3.3  Troubleshooting by Error Message

The following tables provide troubleshooting procedure for each error indicated by the LEDs or STM3 screen. When some parts need to be replaced or repaired, make sure to follow 
the procedure given in Chapter 4 and carry out required adjustments.

3.3.1  Troubleshooting Problems with Error Messages

Table 3-4.  Troubleshooting for Communication Error

Occurrence 

Timing

Symptom

Failed Part

Check Point

Remedy

Reference

At power-on

The printer does not 
work at all.

Panel Board/

Panel FFC

1. Is the Panel FFC not connected to the Panel Board 

and CN5 on the Main Board?

1. Connect the FFC correctly.

4.3.2 “Panel Assy/ 
Cover Open 
Sensor”(p.64)

2. Is the Panel FFC damaged?

2. Replace the Panel FFC.

3. Is the Panel Board damaged?

3. Replace the Panel Board.

P/S ASSY

1. Is the P/S ASSY connector cable not connected to 

CN3 on the Main Board? 

1. Connect the cable correctly.

4.3.3 “P/S Assy”(p.68)

2. Is the P/S ASSY cable or the P/S ASSY itself 

damaged?

2. Replace the P/S ASSY.

* If this does not solve the problem, replace the 

Main Board Assy.

USB cable

1. Is the USB cable not connected to the printer and 

the PC? 

1. Connect the USB cable correctly.

-

Printer driver

1. The printer driver installed on the PC is not the 

one for the Stylus Photo R280/R285/R290?

1. Install the correct printer driver.

-

Main Board

1. The model name written into EEPROM on the 

Main Board is wrong?

1. Write the correct model name to the EEPROM 

using the Adjustment Program.

5.1.1 "Servicing 
Adjustment Item List" 
(P.96)

Summary of Contents for Stylus Photo R290






























































































































Reviews:

No comments