Epson PERFECTION V10 Service Manual Download

Page: 5 / 77

Revision Status

Revision

Date of Issue

Description

June 14, 2006

First release

May 9, 2007

[All chapters]

• The model name; Perfection V200 Photo is added.

[Chapter 1]

• Perfection V200 Photo specs are added to

Table 1-1 “Scanning Speed” (p. 8)

• Perfection V200 Photo specs are added to

“1.2 Basic Specifications” (p. 9)

• Microsoft Windows Vista is added to

“ Environmental Operating Conditions” (p. 10)

• Perfection V200 Photo specs are added to

“1.3 Exterior Specifications” (p. 12)

[Chapter 2]

• Perfection V200 Photo specs are added to

“2.1.3 Carriage Protection Operation” (p. 22)

• Perfection V200 Photo specs are added to

“2.2 Control Circuit” (p. 25)

[Chapter 4]

• Perfection V200 Photo specs are added to

“4.1.4 Packaging and Shipping Cautions” (p. 32)

[Chapter 6]

•

“6.1.2 Lubrication” (p. 59)

Oil type is changed from G-26 to G-45, and Lubrication point of the carriage shaft is added.

[Chapter 7]

• Perfection V200 Photo circuit diagrams are added to

“7.2 Circuit Diagrams” (p. 65)

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands