Epson PERFECTION V10 Service Manual Download

Page: 16 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

PRODUCT DESCRIPTION

Error Handling

1.6 Error Handling

Note *1: Perfection V100 Photo/Perfection V200 Photo/Perfection V350 Photo

*2: Perfection V350 Photo

Table 1-6. Error Definition and Remedy List

Error type

Cause

Scanner Action

Recovery

Command error Received an undefined command or undefined command

parameter.

• No LED indication occurs.
• The scanner ignores the incorrect command or

parameter (Current setting maintained).

• The scanner returns NACK and waits for the next

command parameter.

The scanner recovers from the error by receiving
a correct command.

Fatal error

The main unit is faulty (The lamp is dead. The Carriage does

not return to its home position).

• The red LED flashes.

Turn the scanner off and then back on.

The cover was opened while scanning is in progress.

Close the cover.

The document cover was not removed when scanning strip
films. *

After removing the cover mat, send the
initialization command (ESC @).

The AFL is jammed with strip films.*

After removing the jammed films manually or by
pressing the EJECT button, send the initialization
command (ESC @).

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands