Epson PERFECTION V10 Service Manual Download | Manualshive

Page: 32 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Overview

32

4.1.4 Packaging and Shipping Cautions

This product does not have a Carriage Lock, therefore, during service, make sure to
follow the steps below and move the Carriage to the center of the scanner before
packaging and shipping.

Carriage movement method

1. Turn on the power of Perfection V10/V100 Photo/V200 Photo/V350 Photo.

2. Hold down the following buttons simultaneously for more than three seconds.

Perfection V10 / V100 Photo / V350 Photo
The Start button and the Scan to PDF button

Perfection V200 Photo
The Scan to Mail button and the Copy button

3. Check that the carriage has moved to the center of the scanner.

C A U T I O N

If the Packaging and Shipping Cautions are not kept, the scanner
may break. Also, the function below is special operation only for
service men, and is not open to the users.

«
...
30
31
32
33
34
...
»

Summary of Contents for PERFECTION V10














































































Reviews:

No comments

Related manuals for PERFECTION V10

ImageFormula DR-7080C

Brand: Canon Pages: 4

Brand: Datalogic Pages: 19

Brand: Datalogic Pages: 8

Brand: Datalogic Pages: 32

Brand: Unitech Pages: 41

Brand: e-ImageData Pages: 7

Brand: Pacific Image Electronics Pages: 19

Brand: RIOTEC Pages: 3

Brand: Leuze electronic Pages: 8

rotoScan ROD4 plus Series

Brand: Leuze electronic Pages: 57

Brand: Shining 3D Pages: 83

Brand: Work Pro Pages: 13

MobileOffice H100

Brand: Plustek Pages: 2

Brand: Opticon Pages: 144

Brand: Cannon Pages: 103

Brand: HandHeld Pages: 57

Brand: Radlink Pages: 67

Brand: Zebrex Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands